Miller Electric SRH-503 manual California Proposition 65 Warnings

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. California Proposition 65 Warnings

YWelding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

YBattery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

For Gasoline Engines:

YEngine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

For Diesel Engines:

YDiesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

OM-2236 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Processes OM-2236Description From Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers − Consignes DE Sécurité − À Lire Avant Utilisation Identifie un message de sécurité particulierLE Bruit peut affecter l’ouïe LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LES Pièces Chaudes peuvent cau- ser des brûlures gravesLES Pièces Mobiles peuvent cau- ser des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut FaireInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques − Definitions General Precautionary Label? a Nameplate Safety SymbolsInput Connection Label Do Not LiftSpecifications − InstallationDuty Cycle And Overheating Selecting a Location Volt-Ampere CurvesMovement Location And Airflow Tipping Dimensions And WeightsDimensions w/Running Gear And Lift Eye Be careful when placing or moving unit over uneven surfaces45 m 60 m 70 m 90 m 105 m 120 m Selecting And Preparing Weld Output CablesWeld Cable Sizes 150 ft 200 ft 250 ft 300 ft 350 ftElectrical Service Guide Connecting To Weld Output TerminalsPlacing Jumper Links Welding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Con- nections Controls − OperationElectrode/Amperage Selector Fuse F1 − Maintenance & TroubleshootingRoutine Maintenance Disconnect power before maintaining MonthsTrouble Remedy Troubleshooting TableOM-2236 Circuit Diagram − Electrical DiagramMain Assembly − Parts ListHINGE,CONT Polyolefin Copolymer 2.000 L W/.125H THERMOSTAT,NC Open 135C Close 135C W/INSUL Leads Support ServiceMiller Electric Mfg. Co Owner’s Record

SRH-503 specifications

The Miller Electric SRH-503 is a cutting-edge multiprocess welding machine designed to meet the diverse needs of professional welders. This versatile machine combines various welding processes, including MIG, TIG, and stick welding, making it a perfect choice for fabricators, artists, and maintenance professionals. With its robust build quality and user-friendly design, the SRH-503 provides excellent performance for both light and heavy-duty applications.

One of the standout features of the SRH-503 is its advanced inverter technology, which allows for efficient and stable arc performance. This technology not only improves energy efficiency but also enhances the machine's ability to handle a wide range of materials, from thin sheet metals to thicker plates. The inverter system ensures a consistent welding output, which is essential for achieving high-quality welds in various positions.

Another significant characteristic of the Miller Electric SRH-503 is its dual voltage capability. Operating on either 230V or 460V, the SRH-503 provides flexibility for working in diverse environments and power sources. This feature is particularly beneficial for welders who need to switch between different job sites or who want the convenience of using the machine in various locations.

The SRH-503 is equipped with a digital display that provides real-time feedback on settings and performance. This makes it easier for welders to adjust parameters for optimal results. The machine also includes advanced controls that allow for precise adjustments of welding voltage and amperage, ensuring that users can fine-tune their settings based on the specific needs of their project.

Built with durability in mind, the Miller Electric SRH-503 features a sturdy enclosure that can withstand the rigors of job site conditions. The compact design increases portability, making it easy to transport between locations. Additionally, the machine's intuitive interface allows for quick setup and adjustment, which saves valuable time in fast-paced working environments.

In summary, the Miller Electric SRH-503 is a state-of-the-art welding machine that brings together versatility, advanced technology, and user-friendly features. With its inverter system, dual voltage capability, intuitive controls, and rugged design, this machine is well-suited for professionals seeking reliable and efficient welding solutions. Whether for industrial, fabrication, or repair applications, the SRH-503 delivers exceptional performance and quality.
Top Page Image Contents