Miller Electric SRH-503 manual Principal Safety Standards, EMF Information, About Pacemakers

Page 8

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 (phone: 305-443-9353, website: www.aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers and Piping, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Mi- ami, FL 33126 (phone: 305-443-9353, website: www.aws.org).

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone: 617−770−3000, website: www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1735 Jefferson Davis Highway, Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, web- site: www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone: 800−463−6727 or in Toronto 416−747−4044, website: www.csa−in- ternational.org).

Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 11 West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900, website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, NFPA Standard 51B, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone: 617−770−3000, website: www.nfpa.org and www. sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus- try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, from U.S. Government Printing Office, Super- intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there are 10 Regional Offices−−phone for Region 5, Chicago, is 312−353−2220, website: www.osha.gov).

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields. However, after examining more than 500 studies spanning 17 years of research, a special blue ribbon committee of the National Research Council concluded that: “The body of evidence, in the committee’s judgment, has not demonstrated that exposure to power- frequency electric and magnetic fields is a human-health hazard.” However, studies are still going forth and evidence continues to be examined. Until the final conclusions of the research are reached, you may wish to minimize your exposure to electromagnetic fields when welding or cutting.

To reduce magnetic fields in the workplace, use the following procedures:

1.Keep cables close together by twisting or taping them.

2.Arrange cables to one side and away from the operator.

3.Do not coil or drape cables around your body.

4.Keep welding power source and cables as far away from opera- tor as practical.

5.Connect work clamp to workpiece as close to the weld as possi- ble.

About Pacemakers:

Pacemaker wearers consult your doctor first. If cleared by your doctor, then following the above procedures is recommended.

OM-2236 Page 4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Description OM-2236Processes From Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Identifie un message de sécurité particulier − Consignes DE Sécurité − À Lire Avant UtilisationLE Soudage peut causer un incen- die ou une explosion LES Particules Projetées peu- vent blesser les yeuxLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Bruit peut affecter l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut Faire LES Pièces Mobiles peuvent cau- ser des blessuresConsignes relatives aux stimulateurs cardiaques Principales normes de sécuritéInformation sur les champs électromagnétiques General Precautionary Label − DefinitionsNameplate Safety Symbols Input Connection LabelDo Not Lift ? aDuty Cycle And Overheating − InstallationSpecifications Movement Location And Airflow Volt-Ampere CurvesSelecting a Location Dimensions And Weights Dimensions w/Running Gear And Lift EyeBe careful when placing or moving unit over uneven surfaces TippingSelecting And Preparing Weld Output Cables Weld Cable Sizes150 ft 200 ft 250 ft 300 ft 350 ft 45 m 60 m 70 m 90 m 105 m 120 mConnecting To Weld Output Terminals Electrical Service GuidePlacing Jumper Links Disconnect Device Input Power Con- nections Connecting Input PowerWelding Power Source Input Power Connections − Operation ControlsElectrode/Amperage Selector − Maintenance & Troubleshooting Routine MaintenanceDisconnect power before maintaining Months Fuse F1Troubleshooting Table Trouble RemedyOM-2236 − Electrical Diagram Circuit Diagram− Parts List Main AssemblyHINGE,CONT Polyolefin Copolymer 2.000 L W/.125H THERMOSTAT,NC Open 135C Close 135C W/INSUL Leads Service SupportOwner’s Record Miller Electric Mfg. Co

SRH-503 specifications

The Miller Electric SRH-503 is a cutting-edge multiprocess welding machine designed to meet the diverse needs of professional welders. This versatile machine combines various welding processes, including MIG, TIG, and stick welding, making it a perfect choice for fabricators, artists, and maintenance professionals. With its robust build quality and user-friendly design, the SRH-503 provides excellent performance for both light and heavy-duty applications.

One of the standout features of the SRH-503 is its advanced inverter technology, which allows for efficient and stable arc performance. This technology not only improves energy efficiency but also enhances the machine's ability to handle a wide range of materials, from thin sheet metals to thicker plates. The inverter system ensures a consistent welding output, which is essential for achieving high-quality welds in various positions.

Another significant characteristic of the Miller Electric SRH-503 is its dual voltage capability. Operating on either 230V or 460V, the SRH-503 provides flexibility for working in diverse environments and power sources. This feature is particularly beneficial for welders who need to switch between different job sites or who want the convenience of using the machine in various locations.

The SRH-503 is equipped with a digital display that provides real-time feedback on settings and performance. This makes it easier for welders to adjust parameters for optimal results. The machine also includes advanced controls that allow for precise adjustments of welding voltage and amperage, ensuring that users can fine-tune their settings based on the specific needs of their project.

Built with durability in mind, the Miller Electric SRH-503 features a sturdy enclosure that can withstand the rigors of job site conditions. The compact design increases portability, making it easy to transport between locations. Additionally, the machine's intuitive interface allows for quick setup and adjustment, which saves valuable time in fast-paced working environments.

In summary, the Miller Electric SRH-503 is a state-of-the-art welding machine that brings together versatility, advanced technology, and user-friendly features. With its inverter system, dual voltage capability, intuitive controls, and rugged design, this machine is well-suited for professionals seeking reliable and efficient welding solutions. Whether for industrial, fabrication, or repair applications, the SRH-503 delivers exceptional performance and quality.
Top Page Image Contents