Miller Electric XMT 350 CC/CV Connecting 3-Phase Input Power, = GND/PE Earth Ground Tools Needed

Page 19

4-4. Connecting 3-Phase Input Power

3

= GND/PE Earth Ground

4

7

2

 

 

L1

 

3

 

L2

5

 

6

L3

 

 

 

 

1

Tools Needed:

! Installation must meet all National and Local Codes − have only quali- fied persons make this installation.

! Disconnect and lockout/tagout in- put power before connecting input conductors from unit.

! Always connect green or green/ yellow conductor to supply grounding terminal first, and never to a line terminal.

.The Auto-Line circuitry in this unit au- tomatically adapts the power source to the primary voltage being applied. Check input voltage available at site. This unit can be connected to any in- put power between 208 and 575 VAC without removing cover to relink the power source.

For Three-Phase Operation

1Input Power Cord.

2Disconnect Device (switch shown in the OFF position)

3Green Or Green/Yellow Grounding Conductor

4Disconnect Device Grounding Terminal

5Input Conductors (L1, L2 And L3)

6Disconnect Device Line Terminals

Connect green or green/yellow grounding conductor to disconnect device grounding terminal first.

Connect input conductors L1, L2, and L3 to disconnect device line terminals.

7 Overcurrent Protection

Select type and size of overcurrent protec- tion using Section 4-5(fused disconnect switch shown).

Close and secure door on disconnect device. Remove lockout/tagout device, and place switch in the On position.

804 531-A

OM-2247 Page 15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents File Multiprocess OM-2247212 857NProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-2247 − Introduction SpecificationsCC Mode CV ModeOverheating Duty Cycle And Overheating60% Duty Cycle Minutes Welding Minutes RestingDimensions And Weight − InstallationSelecting a Location Tools Needed Connecting 1-Phase Input PowerEarth GroundFor Three-Phase Operation Connecting 3-Phase Input Power= GND/PE Earth Ground Tools Needed Min Grounding Conductor Size In AWG/Kcmil Electrical Service GuideSingle-Phase Input Voltage Input Amperes At Rated OutputAged, undersized Weld Output Receptacles And Selecting Cable Sizes150 ft 200 ft 250 ft Put terminals Do not use worn, damSocket Information Remote 14 Receptacle InformationOperation Optional Gas Valve Operation And Shielding Gas ConnectionGas flow starts with remote contac- tor on − Operation Power SwitchFront Panel Controls Meter Functions Mode Switch SettingsMode Meter Reading At Idle Meter Reading While Welding Mode Switch Setting Process Output On/Off ControlStick Start Procedure Lift-Arc TIG ProcedureLow OCV Stick Do not remove case when blowing out inside of unit − Maintenance & TroubleshootingBlowing Out Inside Of Unit Voltmeter/Ammeter Help Displays TroubleshootingOM-2247 Circuit Diagram − Electrical Diagram211 328-F Parts Assembly Section −8 − Parts ListPLG1 PLG13 C6,7 214 View of RH Windtunnel Label 6 located on Top of Windtunnel Wrapper/Label Location French UnitsMaterial Thickness Gauge Work like a Pro Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact

XMT 350 CC/CV specifications

The Miller Electric XMT 350 CC/CV is a versatile welding power source designed to meet the demands of various welding applications. Known for its robust performance and advanced features, the XMT 350 is a favorite among professional welders and contractors.

One of the standout features of the XMT 350 is its dual voltage capability, allowing for operation on both standard 230V and 460V power sources. This flexibility makes it an ideal choice for a wide range of job sites and ensures compatibility with various input power situations. The XMT 350 also offers Constant Current (CC) and Constant Voltage (CV) modes, making it suitable for stick, TIG, and MIG welding processes.

Another remarkable characteristic of the XMT 350 is its lightweight and compact design. Weighing only 66 pounds, this welding machine is easy to transport, making it a great option for fieldwork. The durable construction ensures that it can withstand the rigors of job sites while providing reliable performance over time.

The XMT 350 incorporates Miller’s Auto-Set technology, which simplifies the setup process for the user. By automatically adjusting the output parameters based on the material and thickness being welded, Auto-Set helps to optimize welding performance while reducing guesswork. This innovation is particularly beneficial for those who may be less experienced or those looking to improve their efficiency.

Moreover, the XMT 350 features an advanced software system that enhances the machine's performance. The built-in Digital Meter provides accurate readings of voltage and amperage, allowing welders to make precise adjustments for optimal results. This capability is especially valuable for achieving high-quality welds in various materials and thicknesses.

The XMT 350 is also equipped with a number of safety features, including a Thermal Overload Protection system, which prevents overheating by cutting power to the machine when it gets too hot. This ensures the longevity of the unit and protects welders from potential hazards during operation.

In conclusion, the Miller Electric XMT 350 CC/CV is a powerful, versatile, and user-friendly welding machine that caters to various welding applications. Its advanced technologies, including Auto-Set, dual voltage capability, and safety features, make it a reliable choice for both experienced welders and those just starting in the field. With the XMT 350, welders can expect exceptional performance and results across diverse welding tasks.
Top Page Image Contents