Miller Electric XMT 350 CC/CV manual Fire or Explosion hazard, Falling Unit can cause injury

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic- ing unit.

DUse only genuine replacement parts from the manufacturer.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can cause injury.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-2247 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents File Multiprocess OM-2247212 857NProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-2247 − Introduction SpecificationsCC Mode CV ModeOverheating Duty Cycle And Overheating60% Duty Cycle Minutes Welding Minutes RestingDimensions And Weight − InstallationSelecting a Location Tools Needed Connecting 1-Phase Input PowerEarth GroundFor Three-Phase Operation Connecting 3-Phase Input Power= GND/PE Earth Ground Tools Needed Min Grounding Conductor Size In AWG/Kcmil Electrical Service GuideSingle-Phase Input Voltage Input Amperes At Rated OutputAged, undersized Weld Output Receptacles And Selecting Cable Sizes150 ft 200 ft 250 ft Put terminals Do not use worn, damSocket Information Remote 14 Receptacle InformationOperation Optional Gas Valve Operation And Shielding Gas ConnectionGas flow starts with remote contac- tor on − Operation Power SwitchFront Panel Controls Meter Functions Mode Switch SettingsMode Meter Reading At Idle Meter Reading While Welding Mode Switch Setting Process Output On/Off ControlStick Start Procedure Lift-Arc TIG ProcedureLow OCV Stick Do not remove case when blowing out inside of unit − Maintenance & TroubleshootingBlowing Out Inside Of Unit Voltmeter/Ammeter Help Displays TroubleshootingOM-2247 Circuit Diagram − Electrical Diagram211 328-F Parts Assembly Section −8 − Parts ListPLG1 PLG13 C6,7 214 View of RH Windtunnel Label 6 located on Top of Windtunnel Wrapper/Label Location French UnitsMaterial Thickness Gauge Work like a Pro Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact

XMT 350 CC/CV specifications

The Miller Electric XMT 350 CC/CV is a versatile welding power source designed to meet the demands of various welding applications. Known for its robust performance and advanced features, the XMT 350 is a favorite among professional welders and contractors.

One of the standout features of the XMT 350 is its dual voltage capability, allowing for operation on both standard 230V and 460V power sources. This flexibility makes it an ideal choice for a wide range of job sites and ensures compatibility with various input power situations. The XMT 350 also offers Constant Current (CC) and Constant Voltage (CV) modes, making it suitable for stick, TIG, and MIG welding processes.

Another remarkable characteristic of the XMT 350 is its lightweight and compact design. Weighing only 66 pounds, this welding machine is easy to transport, making it a great option for fieldwork. The durable construction ensures that it can withstand the rigors of job sites while providing reliable performance over time.

The XMT 350 incorporates Miller’s Auto-Set technology, which simplifies the setup process for the user. By automatically adjusting the output parameters based on the material and thickness being welded, Auto-Set helps to optimize welding performance while reducing guesswork. This innovation is particularly beneficial for those who may be less experienced or those looking to improve their efficiency.

Moreover, the XMT 350 features an advanced software system that enhances the machine's performance. The built-in Digital Meter provides accurate readings of voltage and amperage, allowing welders to make precise adjustments for optimal results. This capability is especially valuable for achieving high-quality welds in various materials and thicknesses.

The XMT 350 is also equipped with a number of safety features, including a Thermal Overload Protection system, which prevents overheating by cutting power to the machine when it gets too hot. This ensures the longevity of the unit and protects welders from potential hazards during operation.

In conclusion, the Miller Electric XMT 350 CC/CV is a powerful, versatile, and user-friendly welding machine that caters to various welding applications. Its advanced technologies, including Auto-Set, dual voltage capability, and safety features, make it a reliable choice for both experienced welders and those just starting in the field. With the XMT 350, welders can expect exceptional performance and results across diverse welding tasks.
Top Page Image Contents