Miller Electric Axcess manual Installing And Threading Welding Wire

Page 17

4-6. Installing And Threading Welding Wire

Install wire spool. Adjust tension nut so

Install wire guides and

wire is taut when wire feed stops.

anti-wear guide.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressure

 

Indicator

Pressure

Scale

Adjust

 

Rear

Pressure

Rolls

Adjust

 

 

Front

 

Rolls

No Wire Slip

NONCONDUCTIVE

SURFACE

Drive Rolls

Gun Cable

End Of Liner

Install drive rolls.

Wire Slips

NONCONDUCTIVE

SURFACE

Tools Needed:

3/16, 5/64 in

15/16, 3/8 in

. Be sure that outlet cable has proper size

. For soft wire or small diameter stainless

. To adjust drive roll pressure, hold nozzle

liner for the welding wire size. When

steel wire, reduce drive roll pressure on

about 2 in (51 mm) from nonconductive

installing gun,

position

liner

the rear roll to half that of the front rolls.

surface and press gun trigger to feed wire

extending from outlet wire guide as

 

against surface. Tighten knob so wire

close as possible to drive rolls without

 

does not slip. Do not overtighten. If con-

touching.

 

 

 

tact tip is completely blocked, wire should

Install gun. Lay gun cable out straight. Cut off

 

slip at the feeder (see pressure adjust-

 

ment above).Cut wire off. Close cover.

end of wire. Push wire through guides up to

 

 

drive rolls; continue to hold wire. Press Jog

 

 

button to feed wire out gun.

 

 

 

Ref. 156 929-A / Ref. 150 922 / Ref. 156 930 / 802 954 / S-0627-A

OM-211 076 Page 13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Processes OM-211 076HDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSpecifications − Installation− Introduction Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Pin Network Receptacle InformationInstalling And Threading Welding Wire Dual Schedule Switch Option Feeder Display At Power UpPower Source Upper Display Lower Display Voltage Range Upper Display Lower DisplayOperational Terms − OperationPower Switch Front Panel Controls See Section Program Volts Time Arc AdjustSee SectionProgram Push Button Volts Arc AdjustUpper Display Upper DisplayLower Display Sequence Trigger Control Trigger Hold Feeder Set Up Feeder Set Up Push ButtonAdjust Control Make a selection, rotate the Adjust control Process Set Up Push ButtonJog/Purge Jog/Purge Push Button Adjust Control Gun Trigger ReceptacleWelding and to preset gas pressure at the regulator Pulse Reset ModeMild Steel Accu-pulseSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program Routine Maintenance − MaintenanceDiagnostics Indicates a trigger Closed errorTrouble Remedy TroubleshootingDisconnect power before troubleshooting OM-211 076 Circuit Diagram − Electrical Diagram211 005-E − Fig 21 − Fig − Parts ListPart Description Quantity Control Box PLG4 Drive Assembly, Wire 1.4 mm 1.2 mmPage Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s
Top Page Image Contents