Miller Electric Axcess manual Jog/Purge Push Button Adjust Control Gun Trigger Receptacle

Page 26

5-10. Jog/Purge

1 Jog/Purge Push Button

2 Adjust Control

3 Gun Trigger Receptacle

2

3

1

803 505-A

Pressing the Jog/Purge switch allows the operator to jog wire without energizing the weld power or gas valve circuit.

•The unit provides the ability to jog the wire feeder by means of the gun trigger or the Jog/Purge switch. If the welding arc does not initiate in 3 seconds after the gun trigger is activated, the unit will perform a jog operation for a maximum of 30 seconds. If the gun trigger is still activated after 30 seconds, the jog operation is terminated to prevent complete unspooling of the wire, in the case of a damaged gun. The unit

displays the “ERR STRT“ message to inform the operator that the trigger is activated.

•Jog speed can be adjusted by the Adjust control when the unit is jogging wire. The unit displays jog speed when the unit is being jogged.

•Jogging can also be accomplished by pressing the Jog/Purge button.

•Pressing the Jog/Purge button also allows the operator to purge gas lines before

welding and to preset gas pressure at the regulator.

•This unit is equipped with Auto Thread capability. By rocking the switch from purge to jog within 0.5 seconds will automatically feed wire for a factory default setting of 192 in (4877 mm) of wire before stopping. The default feed rate is 700 ipm. These settings can be changed using an optional PDA with File Management software. Pressing the Jog/Purge switch or gun trigger during Auto Threading will terminate the automatic feed operation.

OM-211 076 Page 22

Image 26

Contents Description OM-211 076HProcesses File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Introduction − InstallationSpecifications Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation TableInstalling And Threading Welding Wire Power Source Upper Display Lower Display Voltage Range Feeder Display At Power UpDual Schedule Switch Option Upper Display Lower Display− Operation Operational TermsPower Switch See See Section Program Volts Time Arc AdjustFront Panel Controls SectionUpper Display Volts Arc AdjustProgram Push Button Upper DisplayLower Display Sequence Trigger Control Trigger Hold Feeder Set Up Feeder Set Up Push ButtonAdjust Control Process Set Up Push Button Make a selection, rotate the Adjust controlJog/Purge Jog/Purge Push Button Adjust Control Gun Trigger ReceptacleWelding and to preset gas pressure at the regulator Mild Steel Reset ModePulse Accu-pulseSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program − Maintenance Routine MaintenanceDiagnostics Closed error Indicates a triggerTrouble Remedy TroubleshootingDisconnect power before troubleshooting OM-211 076 − Electrical Diagram Circuit Diagram211 005-E − Parts List − Fig 21 − FigPart Description Quantity Control Box PLG4 Drive Assembly, Wire 1.2 mm 1.4 mmPage Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s