Miller Electric Axcess manual Setting Sequence Parameters, Sequence Parameters In a Program

Page 28

SECTION 6 − SETTING SEQUENCE PARAMETERS

6-1. Sequence Parameters In A Program

	Sequence		Parameters





		Volts/Trim	IPM	Seconds

1.	Preflow			Off-5.0

2.	Postflow			Off-5.0

3.	Start	10.0-44.0/	40-1400/	Off-5.0
3.	Start	0-99	0-99	Off-5.0
		0-99	0-99

4.	Crater	10.0-44.0/	40-1400/	Off-5.0
4.	Crater	0-99	0-99	Off-5.0
		0-99	0-99

.For more information on

Sequence mode, see Feeder Set Up Push Button in Section 5-7.

If time is set to Off in Weld sequence, welding continues until gun trigger is released.

If time is set to zero in any timed sequence except Weld, the sequence is skipped.

.Maximum IPM may actually

be lower depending on wire size and gas combination.

X = Setting available.

				Weld
				Crater
				Time
		Start
	Preflow	Time			Postflow
	Preflow				Postflow
	Time				Time
					Time
						Time
Preflow		Start	Weld	Crater	Postflow	Sequence
						End
Trigger				Trigger
Pressed				Released

OM-211 076 Page 24

Image 28

Contents OM-211 076H ProcessesDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Installation Specifications− Introduction Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation TableInstalling And Threading Welding Wire Feeder Display At Power Up Dual Schedule Switch OptionPower Source Upper Display Lower Display Voltage Range Upper Display Lower Display− Operation Operational TermsPower Switch See Section Program Volts Time Arc Adjust Front Panel ControlsSee SectionVolts Arc Adjust Program Push ButtonUpper Display Upper DisplayLower Display Adjust Control Feeder Set Up Push ButtonSequence Trigger Control Trigger Hold Feeder Set Up Process Set Up Push Button Make a selection, rotate the Adjust controlWelding and to preset gas pressure at the regulator Jog/Purge Push Button Adjust Control Gun Trigger ReceptacleJog/Purge Reset Mode PulseMild Steel Accu-pulseSequence Parameters In a Program − Setting Sequence ParametersSequence Parameters − Maintenance Routine MaintenanceDiagnostics Closed error Indicates a triggerDisconnect power before troubleshooting TroubleshootingTrouble Remedy OM-211 076 − Electrical Diagram Circuit Diagram211 005-E − Parts List − Fig 21 − FigPart Description Quantity Control Box PLG4 Drive Assembly, Wire 1.2 mm 1.4 mmPage Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s