Miller Electric 75 manual Power Switch, General Terms Crater, Postflow, Feeder Set Up, Auto Thread

Page 23

General Terms:

 

Crater

Allows setting of voltage/arc adjust, wire feed rate, and time value for arc ends.

Postflow

Setting a time value for gas flow after arc end.

Feeder Set Up

Allow selection of Sequence and trigger functions.

Auto Thread

Method of jogging wire without holding jog or trigger switch. Pressing Jog and Retract simultaneously

 

will automatically feed wire. Default setting is 192 at a feed rate of 700 ipm (these values can be

 

changed using a PDA with File Management/WaveWriter software). Pressing jog, purge, or trigger

 

switch will terminate the auto-threading feature.

5-2.

Power Switch

 

 

1

Power Switch

 

1

 

 

 

804 587-A

OM-228 956 Page 19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents File Advanced Manufacturing Systems OM-228 956BProcesses DescriptionFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSelecting a Location − InstallationSpecifications − IntroductionConnection Diagram Tools Needed 9/16, 5/8 Rear Panel Connections And Rotating Drive AssemblyRemoval Installing Drive RollsInstallation Pin Network Receptacle InformationInstalling PD continuous wire guides with PD drive rolls Installing PD Continuous Wire GuidesTools Needed 16, 1/8, 5/32 Installing Non-PD Old Style Wire GuidesInstalling wire guides with non- PD old-style drive rolls Rotate guide holder 180 degrees and reinstallInstalling gun without Accu- Mate connection Installing Welding GunInstalling gun with Accu-Mate connection Secure gun by tightening power clamp knobEnd Of Liner No Wire SlipWire Slips Upper Display Lower Display Feeder Display At Power UpDual Schedule Switch Options Power Source Upper Display Lower Display Voltage RangeOperational Terms − OperationPostflow Power SwitchFeeder Set Up General Terms CraterSection See Section Program Volts Time Arc AdjustFront Panel Controls SeeUpper Display Volts Arc AdjustProgram Push Button Upper DisplayLower Display Sequence Trigger Control Trigger Hold Feeder Set Up Feeder Set Up Push ButtonAdjust Control Make a selection, rotate the Adjust control Process Set Up Push ButtonJog/Purge Jog/Purge Push Button Adjust Control Gun Trigger ReceptacleWelding and to preset gas pressure at the regulator Accu-pulse Reset ModePulse Mild SteelSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program = Check = Change ~ = Clean = Replace − MaintenanceRoutine Maintenance Disconnect power before maintainingIndicates a voltage Sense error DiagnosticsIndicates a memory CRC PCM error Indicates a line errorIndicates an arc error Indicates a polarity errorUnknown TroubleshootingDisconnect power before troubleshooting RMD done message indicatesCircuit Diagram − Electrical Diagram211 005-D − -3 21 − Fig − Parts ListFigures 9-3 Control Box PLG4 Drive Assembly, Wire 9-1Item Drive Assembly, WireDrive Assembly, Wire -1Item Wire Size Page Page Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact
Top Page Image Contents