Miller Electric 75 manual Miller Electric Mfg. Co, To locate a Distributor or Service Agency visit

Page 48

Owner’s Record

Please complete and retain with your personal records.

Model Name	Serial/Style Number

Purchase Date	(Date which equipment was delivered to original customer.)

Distributor

Address

City

State	Zip

For Service

Contact a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:	Welding Supplies and Consumables
	Options and Accessories
	Personal Safety Equipment
	Service and Repair
	Replacement Parts
	Training (Schools, Videos, Books)
	Technical Manuals (Servicing Information
	and Parts)
	Circuit Diagrams
	Welding Process Handbooks
	To locate a Distributor or Service Agency visit
	www.millerwelds.com or call 1-800-4-A-Miller

Contact the Delivering Carrier to:	File a claim for loss or damage during
	shipment.
	For assistance in filing or settling claims, contact
	your distributor and/or equipment manufacturer’s
	Transportation Department.
PRINTED IN USA	♥ 2006 Miller Electric Mfg. Co. 2006−01

Miller Electric Mfg. Co.

An Illinois Tool Works Company

1635 West Spencer Street

Appleton, WI 54914 USA

International Headquarters−USA

USA Phone: 920-735-4505 Auto-Attended

USA & Canada FAX: 920-735-4134

International FAX: 920-735-4125

European Headquarters −

United Kingdom

Phone: 44 (0) 1204-593493

FAX: 44 (0) 1204-598066

www.MillerWelds.com

Image 48

Contents OM-228 956B ProcessesDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Installation Specifications− Introduction Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Tools Needed 9/16, 5/8Installing Drive Rolls InstallationPin Network Receptacle Information RemovalInstalling PD Continuous Wire Guides Installing PD continuous wire guides with PD drive rollsInstalling Non-PD Old Style Wire Guides Installing wire guides with non- PD old-style drive rollsRotate guide holder 180 degrees and reinstall Tools Needed 16, 1/8, 5/32Installing Welding Gun Installing gun with Accu-Mate connectionSecure gun by tightening power clamp knob Installing gun without Accu- Mate connectionNo Wire Slip Wire SlipsEnd Of Liner Feeder Display At Power Up Dual Schedule Switch OptionsPower Source Upper Display Lower Display Voltage Range Upper Display Lower Display− Operation Operational TermsPower Switch Feeder Set UpGeneral Terms Crater PostflowSee Section Program Volts Time Arc Adjust Front Panel ControlsSee SectionVolts Arc Adjust Program Push ButtonUpper Display Upper DisplayLower Display Feeder Set Up Push Button Adjust ControlSequence Trigger Control Trigger Hold Feeder Set Up Process Set Up Push Button Make a selection, rotate the Adjust controlJog/Purge Push Button Adjust Control Gun Trigger Receptacle Welding and to preset gas pressure at the regulatorJog/Purge Reset Mode PulseMild Steel Accu-pulse− Setting Sequence Parameters Sequence Parameters In a ProgramSequence Parameters − Maintenance Routine MaintenanceDisconnect power before maintaining = Check = Change ~ = Clean = ReplaceDiagnostics Indicates a voltage Sense errorIndicates a line error Indicates an arc errorIndicates a polarity error Indicates a memory CRC PCM errorTroubleshooting Disconnect power before troubleshootingRMD done message indicates Unknown− Electrical Diagram Circuit Diagram211 005-D − Parts List − -3 21 − FigFigures 9-3 Control Box PLG4 Drive Assembly, Wire Drive Assembly, Wire 9-1ItemDrive Assembly, Wire -1Item Wire Size Page Page Service Your distributor also givesSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s