
Cisco 7200 Series and the 4R Port Adapter
Caution Do not slide the port adapter all the way into the slot until you have connected all required cables. Trying to do so will disrupt normal operation of the router.
Step 5 With the port adapter halfway in the slot, connect all required cables to the port adapter.
Step 6 After connecting all required port adapter cables, carefully slide the port adapter all the way into the slot until you feel the port adapter’s connectors seat in the midplane.
Step 7 Move the port adapter lever to the locked position. shows the port adapter lever in the locked position.
Note If the port adapter lever does not move to the locked position, the port adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, reinsert it, and move the port adapter lever to the locked position.
Figure 19 Placing the Port Adapter Lever in the Locked Position (Cisco 7206 Shown)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TOKEN RING |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ETHERNET 10BT |
|
|
|
|
|
|
|
| FAST ETHERNET |
|
|
|
|
|
|
|
| ENABLED |
|
|
|
| K |
|
| 5 |
|
| |
|
|
|
|
|
|
| M | II |
| IN | R | J 4 |
| 4 | |||
|
|
|
|
|
|
| L |
|
|
| |||||||
3 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FAST SERIAL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SLOT | 1 | FE | MII |
| FAST ETHERNET INPUT/OUTPUT CONTROLLER |
| H6747 | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 | |||
ENABLED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
PCMCIA | EJECT | SLOT | 0 |
|
| MII | RJ45 | RJ45 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
| EN | EN | LINK |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| Port adapter |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| handle |
|
|
|
|
|
|
|
|
|
Note: This adapter installation applies to any port or service adapter.
Port adapter lever (locked position)
This completes the procedure for installing a new port adapter in a Cisco 7200 series router.
Attaching 4R Port Adapter Interface Cables
The Token Ring ports on the 4R port adapter run at either 4 or 16 Mbps. You need one Token Ring interface cable for each 4R port adapter interface you want to use. Token Ring interface cables are not available from Cisco Systems, but are commercially available through outside cable vendors. Port adapters have a handle but this handle is not shown in to allow a full view of detail on the 4R port adapter’s faceplate.
Use the following procedure to attach Token Ring cables to the 4R port adapter:
30 |
| |
|