Cisco Systems PA-4R manual Using the ping Command

Page 26

VIP2 and the 4R Port Adapter

Physical slot 8, ~physical slot 0x7, logical slot 8, CBus 0

Microcode Status 0x4

Master Enable, LED,

WCS

Loaded

 

 

 

 

 

 

 

Board is analyzed

 

 

 

 

 

 

 

 

 

 

 

Pending I/O Status: None

 

 

 

 

 

 

 

 

EEPROM format

version 1

 

 

 

 

 

 

 

 

 

VIP2 controller, HW

rev

2.2, board revision UNKNOWN

 

Serial number: 03341418

Part number:

73-1684-02

 

Test history:

0x00

 

RMA number:

00-00-00

 

 

Flags: cisco 7000 board; 7500 compatible

 

 

 

 

EEPROM contents (hex):

 

 

 

 

 

 

 

 

 

0x20: 01 15

02 02

00 32 FC 6A 49 06

94

02 00

00 00 00

0x30:

07

2B

00

2A

1A

00 00

00

00

00

00

00

00

00 00

00

Slot database information:

Flags: 0x4 Insertion time: 0x3188 (01:20:53 ago)

Controller Memory Size: 8 MBytes

PA Bay 0 Information:

Token Ring PA, 4 ports

EEPROM format version 1

HW rev 1.1, Board revision 0

Serial number: 02827613 Part number: 73-1390-04

PA Bay 1 Information:

Token Ring PA, 4 ports

EEPROM format version 1

HW rev 1.1, Board revision 88

Serial number: 02023786 Part number: 73-1390-04

Using the ping Command

The ping command allows you to verify that an interface port is functioning properly and to check the path between a specific port and connected devices at various locations on the network. This section provides brief descriptions of the ping command. After you verify that the system and VIP2 have booted successfully and are operational, you can use this command to verify the status of interface ports.

The ping command sends an echo request out to a remote device at an IP address that you specify. After sending a series of signals, the command waits a specified time for the remote device to echo the signals. Each returned signal is displayed as an exclamation point (!) on the console terminal; each signal that is not returned before the specified time-out is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed]

indicate that the connection failed.

Following is an example of a successful ping command to a remote server with the address 1.1.1.10:

Router# ping 1.1.1.10 <Return> Type escape sequence to abort.

Sending 5, 100-byte ICMP Echoes to 1.1.1.10, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router#

If the connection fails, verify that you have the correct IP address for the server and that the server is active (powered on), and repeat the ping command.

For complete descriptions of interface subcommands and the configuration options available for VIP2-related interfaces, and which support VIP2 functionality, refer to the publications listed in the section “If You Need More Information” on page 2.

PA-4R Half-Duplex Token Ring Port Adapter Installation and Configuration

26

OL-3589-01

 

 

Image 26
Contents Contents Port Adapter Installation Prerequisites Software and Hardware RequirementsList of Parts and Tools Safety GuidelinesChecking Hardware and Software Compatibility Safety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Token Ring SpecificationsToken Ring Overview IBM Token Ring and Ieee 802.5 Comparison Token Ring Connection Equipment Token Ring Distance LimitationsWhat Is the 4R Port Adapter? Token Ring Speed ConsiderationsDram 4R Port Adapter LEDs Port adapter slot Blank port adapter4R Port Adapter Receptacles, Cables, and Pinouts 4R Port Adapter CablesVIP2 and the 4R Port Adapter 4R Port Adapter Receptacle PinoutInstalling or Replacing a Port Adapter on a VIP2 Location of Port Adapter Screw Partial Port Adapter View Aligning a Port Adapter in a Port Adapter Slot H3152 Attaching 4R Port Adapter Interface Cables Token Ring Interface Cable ConnectionsConfiguring the 4R Interfaces Using the Exec Command Interpreter At the Exec prompt for a router, enter the enable commandUsing the Setup Command Facility BracketsConfiguring Interfaces Using the configure Command Configuring interface parametersChange the default shutdown state and enable the interface Checking the Configuration Using show Commands to Verify the VIP2 StatusRouter# sh int tokenring 3/0/0 Using the ping Command Cisco 7200 Series and the 4R Port Adapter 4R port adapterRemoving a Port Adapter Replacing a Port Adapter Handling a Port AdapterPort adapter Handle Configuring the 4R Interfaces Cisco 7200 Series and the 4R Port Adapter Configuring Interfaces Routerconfig-if#ip address 1.1.1.10Using show Commands to Verify the New Interface Status Using show Commands to Display Interface Information Board revision A0 Serial number 2023868 Part number Router# ping 1.1.1.10 Return Type escape sequence to abort Related Documentation Obtaining Documentation, Obtaining Technical Assistance,Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationTechnical Assistance Center Obtaining Technical AssistanceCisco.com Cisco TAC Web Site Cisco TAC Escalation CenterOL-3589-01