Cisco Systems PA-4R manual Related Documentation

Page 38

Related Documentation

Related Documentation

The documentation listed below is available online, on the Documentation CD-ROM, or as printed documents.

Your router, switch, or gateway and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources:

•Cisco IOS software:

–For configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware.

–To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com: http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl. You must be a registered user on Cisco.com to access this tool.

Note You can access Cisco IOS software configuration and hardware installation and maintenance documentation on the World Wide Web at http://www.cisco.com/public/countries_languages.shtml.

•Cisco 7200 series routers:

–For port adapter hardware and memory configuration guidelines, refer to the Cisco 7200 Series Port Adapter Hardware Configuration Guidelines.

–For hardware installation and maintenance information (including the Cisco 7206 or Cisco 7206VXR as a router shelf in a Cisco AS5800 Universal Access Server), refer to the installation and configuration guide that shipped with your Cisco 7200 series router.

–For information on network processing engines or network services engines, refer to the Network Processing Engine and Network Services Engine Installation and Configuration publication.

–For information on the router boot images, refer to the Cisco 7200 Series Routers Boot Images Information publication.

•Cisco 7500 series routers:

For hardware installation and maintenance information, refer to the following publications:

–Cisco 7500 Installation and Configuration or the quick start guide that shipped with your router

–Second-Generation Versatile Interface Processor (VIP2) Installation and Configuration

•For international agency compliance, safety, and statutory information for WAN interfaces:

–Regulatory Compliance and Safety Information for the Cisco 7200 Series Routers

–Regulatory Compliance and Safety Information for the Cisco 7500 Series Routers

–Site Preparation and Safety Guide

•To view Cisco documentation or obtain general information about the documentation, refer to the following sections:

–Obtaining Documentation, page 39

–Obtaining Technical Assistance, page 40

PA-4R Half-Duplex Token Ring Port Adapter Installation and Configuration

38

OL-3589-01

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Contents Port Adapter Installation Prerequisites Software and Hardware RequirementsList of Parts and Tools Safety GuidelinesChecking Hardware and Software Compatibility Safety Warnings Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Token Ring SpecificationsToken Ring Overview IBM Token Ring and Ieee 802.5 Comparison Token Ring Connection Equipment Token Ring Distance LimitationsWhat Is the 4R Port Adapter? Token Ring Speed ConsiderationsDram 4R Port Adapter LEDs Port adapter slot Blank port adapter4R Port Adapter Receptacles, Cables, and Pinouts 4R Port Adapter CablesVIP2 and the 4R Port Adapter 4R Port Adapter Receptacle PinoutInstalling or Replacing a Port Adapter on a VIP2 Location of Port Adapter Screw Partial Port Adapter View Aligning a Port Adapter in a Port Adapter Slot H3152 Attaching 4R Port Adapter Interface Cables Token Ring Interface Cable ConnectionsConfiguring the 4R Interfaces Using the Exec Command Interpreter At the Exec prompt for a router, enter the enable commandUsing the Setup Command Facility BracketsConfiguring Interfaces Using the configure Command Configuring interface parametersChange the default shutdown state and enable the interface Checking the Configuration Using show Commands to Verify the VIP2 StatusRouter# sh int tokenring 3/0/0 Using the ping Command Cisco 7200 Series and the 4R Port Adapter 4R port adapterRemoving a Port Adapter Replacing a Port Adapter Handling a Port AdapterPort adapter Handle Configuring the 4R Interfaces Cisco 7200 Series and the 4R Port Adapter Configuring Interfaces Routerconfig-if#ip address 1.1.1.10Using show Commands to Verify the New Interface Status Using show Commands to Display Interface Information Board revision A0 Serial number 2023868 Part number Router# ping 1.1.1.10 Return Type escape sequence to abort Related Documentation Obtaining Documentation, Obtaining Technical Assistance,Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationTechnical Assistance Center Obtaining Technical AssistanceCisco.com Cisco TAC Web Site Cisco TAC Escalation CenterOL-3589-01
Top Page Image Contents