Makita GA4030, GA5030, GA4530 Assembly, Switch action Installing or removing wheel guard

Page 5

Switch action

Installing or removing wheel guard

1

009423

CAUTION:

1. Switch lever

1

2

3

009425

CAUTION:

1.Wheel guard

2.Screw

3.Bearing box

•Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when the rear of the slide switch is depressed.

•Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool.

To start the tool, slide the switch lever toward the "I (ON)" position. For continuous operation, press the front of the switch lever to lock it.

To stop the tool, press the rear of the switch lever, then slide it toward the "O (OFF)" position.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

Installing side grip (handle)

•When using a depressed center grinding wheel/Multi-disc, flex wheel, wire wheel brush, cut-off wheel or diamond wheel, the wheel guard

must be fitted on the tool so that the closed side of the guard always points toward the operator.

Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work. Be sure to tighten the screw securely.

To remove wheel guard, follow the installation procedure in reverse.

Installing or removing depressed center grinding wheel/Multi-disc

11. Lock nut

22. Depressed

3center grinding

wheel/Multi-disc4

3. Ring

4. Inner flange

009424

CAUTION:

•Always be sure that the side grip is installed

securely before operation.

Screw the side grip securely on the position of the tool as shown in the figure.

009426

WARNING:

•Always use supplied guard when depressed center

grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury.

Mount the inner flange onto the spindle. Fit the wheel/disc on the inner flange and screw the lock nut onto the spindle.

To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Angle Grinder Meuleuse dAngle Esmeriladora Angular General Safety Rules Specifications120 25 ft 50 ft 100 ft 150 ft More Than Not More Than Specific Safety RulesMinimum gage for cord Ampere Rating Volts Shaft lock SymbolsFunctional Description Installing side grip handle AssemblySwitch action Installing or removing wheel guard Installing or removing abrasive disc optional accessory Installing or removing flex wheel optional accessoryOperation Grinding and sanding operationAccessories MaintenanceOperation with wire cup brush optional accessory Operation with wire wheel brush optional accessory009438 Makita Limited ONE Year Warranty Règles de sécurité générales Conservez CE Mode DemploiSpécifications La présence de poussière dans lair Règles DE Sécurité Particulières Description DU Fonctionnement SymbolesBlocage de larbre InterrupteurAssemblage Installation de la poignée latérale poignéeInstallation ou retrait du carter de meule Opérations de meulage et de ponçage UtilisationEntretien Accessoires009438 Garantie Limitée D’UN AN Makita Guarde Estas Instrucciones EspecificacionesNormas Generales DE Seguridad Reduce los riesgos relacionados con el polvo Más de No más de Calibre del cable AWG 10 a Normas Específicas DE Seguridad Advertencias y precauciones12 a 16 a No se recomiendaSímbolos Descripción DEL FuncionamientoBloqueo del eje Accionamiento del interruptorInstalación o desmontaje del protector guarda de disco EnsambleInstalación de la empuñadura lateral mango Operación con carda de alambres accesorio opcional OperaciónOperación de esmerilado y lijado Accesorios Mantenimiento009438 Política de garantía Advertencia
Related manuals
Manual 13 pages 41.19 Kb

GA4030, GA4530, GA5030 specifications

Makita is renowned for its high-performance power tools, and the GA5030, GA4530, and GA4030 angle grinders are no exception. These models exemplify Makita's commitment to innovation, durability, and user-friendly design, making them ideal for both professional tradespeople and DIY enthusiasts.

The Makita GA5030 is a compact and versatile angle grinder equipped with a powerful 5-inch wheel. One of its standout features is its lightweight design, which minimizes fatigue during prolonged use. The GA5030 boasts an 8.5-amp motor capable of delivering up to 11,000 RPM, providing swift and efficient material removal. This model also integrates a labrynth construction that seals and protects the motor and bearings from dust and debris, enhancing the tool’s longevity. Additionally, its ergonomic rubberized grip ensures comfort and control, making it suitable for a variety of applications, from metalworking to masonry.

Moving onto the GA4530, this 4.5-inch angle grinder balances power and portability. Like the GA5030, it is powered by a robust 7.5-amp motor that generates a no-load speed of 10,000 RPM. Its compact design allows for easier handling in tight spaces, making it ideal for both home projects and professional jobs. An important feature of the GA4530 is the protective cover that can be adjusted without tools, allowing for quick changes based on the job at hand. Moreover, this model includes an automatic shut-off carbon brush system that extends the life of the motor, ensuring lasting performance.

Lastly, the GA4030 serves as an excellent choice for those seeking a smaller, yet powerful tool. This 4-inch angle grinder is equipped with a 6.0-amp motor capable of reaching speeds up to 10,000 RPM. The GA4030’s slim body design allows for easy handling, while its rubberized grip provides added comfort and reduces vibrations. This model also features a metal gear housing for increased durability, making it suitable for heavy-duty applications.

In summary, the Makita GA5030, GA4530, and GA4030 are outstanding angle grinders, each offering unique features and capabilities to cater to various needs. With their powerful motors, durable construction, and user-friendly designs, these tools reflect Makita’s high standards in professional-grade equipment. Whether you are a seasoned professional or a weekend DIYer, these grinders will undoubtedly enhance your workflow and deliver exceptional results.
Top Page Image Contents