Makita GA4530, GA5030 Maintenance, Accessories, Operation with wire cup brush optional accessory

Page 7

Operation with wire cup brush (optional accessory)

1. Wire cup brush

1

009436

CAUTION:

•

Check operation of brush by running tool with no

the wrenches.

When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage.

MAINTENANCE

CAUTION:

•Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.

•Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

 

load, insuring that no one is in front of or in line with

 

brush.

•

Do not use brush that is damaged, or which is out of

balance. Use of damaged brush could increase potential for injury from contact with broken brush wires.

Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire cup brush onto spindle and tighten with

1

2

009428

1.Exhaust vent

2.Inhalation vent

supplied wrench. When using brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage.

Operation with wire wheel brush (optional accessory)

 

1. Wire wheel

1

brush

009437

CAUTION:

•Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush.

•Do not use wire wheel brush that is damaged, or which is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires.

•ALWAYS use guard with wire wheel brushes,

assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury.

Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with

The tool and its air vents have to be kept clean. Regularly clean the tool's air vents or whenever the vents start to become obstructed.

To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

•Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc, flex wheel and wire wheel brush. If you decide to use your Makita grinder with approved accessories

which you purchase from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Angle Grinder Meuleuse dAngle Esmeriladora Angular General Safety Rules SpecificationsMinimum gage for cord Ampere Rating Volts Specific Safety Rules120 25 ft 50 ft 100 ft 150 ft More Than Not More Than Functional Description SymbolsShaft lock Switch action Installing or removing wheel guard AssemblyInstalling side grip handle Grinding and sanding operation Installing or removing flex wheel optional accessoryInstalling or removing abrasive disc optional accessory OperationOperation with wire wheel brush optional accessory MaintenanceAccessories Operation with wire cup brush optional accessory009438 Makita Limited ONE Year Warranty Spécifications Conservez CE Mode DemploiRègles de sécurité générales La présence de poussière dans lair Règles DE Sécurité Particulières Interrupteur SymbolesDescription DU Fonctionnement Blocage de larbreInstallation ou retrait du carter de meule Installation de la poignée latérale poignéeAssemblage Opérations de meulage et de ponçage UtilisationEntretien Accessoires009438 Garantie Limitée D’UN AN Makita Normas Generales DE Seguridad EspecificacionesGuarde Estas Instrucciones Reduce los riesgos relacionados con el polvo 16 a No se recomienda Normas Específicas DE Seguridad Advertencias y precaucionesMás de No más de Calibre del cable AWG 10 a 12 aAccionamiento del interruptor Descripción DEL FuncionamientoSímbolos Bloqueo del ejeInstalación de la empuñadura lateral mango EnsambleInstalación o desmontaje del protector guarda de disco Operación de esmerilado y lijado OperaciónOperación con carda de alambres accesorio opcional Accesorios Mantenimiento009438 Política de garantía Advertencia
Related manuals
Manual 13 pages 41.19 Kb

GA4030, GA4530, GA5030 specifications

Makita is renowned for its high-performance power tools, and the GA5030, GA4530, and GA4030 angle grinders are no exception. These models exemplify Makita's commitment to innovation, durability, and user-friendly design, making them ideal for both professional tradespeople and DIY enthusiasts.

The Makita GA5030 is a compact and versatile angle grinder equipped with a powerful 5-inch wheel. One of its standout features is its lightweight design, which minimizes fatigue during prolonged use. The GA5030 boasts an 8.5-amp motor capable of delivering up to 11,000 RPM, providing swift and efficient material removal. This model also integrates a labrynth construction that seals and protects the motor and bearings from dust and debris, enhancing the tool’s longevity. Additionally, its ergonomic rubberized grip ensures comfort and control, making it suitable for a variety of applications, from metalworking to masonry.

Moving onto the GA4530, this 4.5-inch angle grinder balances power and portability. Like the GA5030, it is powered by a robust 7.5-amp motor that generates a no-load speed of 10,000 RPM. Its compact design allows for easier handling in tight spaces, making it ideal for both home projects and professional jobs. An important feature of the GA4530 is the protective cover that can be adjusted without tools, allowing for quick changes based on the job at hand. Moreover, this model includes an automatic shut-off carbon brush system that extends the life of the motor, ensuring lasting performance.

Lastly, the GA4030 serves as an excellent choice for those seeking a smaller, yet powerful tool. This 4-inch angle grinder is equipped with a 6.0-amp motor capable of reaching speeds up to 10,000 RPM. The GA4030’s slim body design allows for easy handling, while its rubberized grip provides added comfort and reduces vibrations. This model also features a metal gear housing for increased durability, making it suitable for heavy-duty applications.

In summary, the Makita GA5030, GA4530, and GA4030 are outstanding angle grinders, each offering unique features and capabilities to cater to various needs. With their powerful motors, durable construction, and user-friendly designs, these tools reflect Makita’s high standards in professional-grade equipment. Whether you are a seasoned professional or a weekend DIYer, these grinders will undoubtedly enhance your workflow and deliver exceptional results.
Top Page Image Contents