Grizzly G0582, G9962Z, 9962ZX, G0445 instruction manual Pressure Roller Test Start Up

Page 21

Pressure Roller Test

Start Up

 

 

 

 

 

 

The pressure rollers have been set at the factory, but for your safety, you should verify that they are set below the level of the sanding roller.

It is absolutely essential to keep the pres- sure rollers set below the level of the sand- ing roller. If the pressure rollers are even, or higher than the sanding roller, the wood WILL be propelled from the sander at a high rate of speed. This situation could cause serious kick-back injury.

To check the pressure roller height:

1.DISCONNECT THE SANDER FROM THE POWER SOURCE!

2.Place a piece of scrap wood of uniform thickness across the table so it spans both the front and the rear pressure rollers at the same time.

3.With the air pressure connected and the sanding belt installed and tensioned, manu- ally raise the table and verify that the board touches both pressure rollers before it touch- es the sanding belt.

Note: If the board does not touch both pres- sure rollers before it touches the sanding belt, then the pressure rollers must be adjusted before operation. Refer to Pressure Rollers on Page 33.

Serious personal injury could result if the machine is connected to the power source during assembly or adjustment. Wait until the machine is turned OFF, unplugged, and all working parts have come to a complete stop before you attempt to assemble or adjust the machine!

Loose hair and cloth- ing could get caught in machinery causing serious personal inju- ry. Keep loose clothing rolled up and long hair tied up and away from machinery.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during start up.

Before starting the machine:

1.Read this manual and make sure you take all safety precautions before operating this machine.

2.Make sure the machine is connected to an air compressor and the pressure gauge reads 75 PSI.

3.Make sure all tools or foreign objects have been removed from the conveyor surface, the top of the machine, and the inside of the machine.

4.Make sure all the wiring is correct.

Image 21
Contents Model Page Table of Contents Warranty & Returns Introduction ForewordContact Info Features External FeaturesControl Panel Internal Features Machine Data Sheet G0445 Machine Data Sheet G0582 Machine Data Sheet G9962Z Machine Data Sheet G9962ZX Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wide Belt Sanders 220V/440V Connection Circuit RequirementsExtension Cords Grounding440V Connection Site Considerations Clean UpBeginning Assembly SetupAir Line Installation SectionInventory Crate contents, see FigureDust Collection To hook up a dust collection systemSanding Belt To install the sanding beltPressure Roller Test Start Up Recommended Adjustments Operations Operation SafetyChoosing Sandpaper GritTable Movement Adjusting Feed RateAmp Draw Meter Platen Adjustment Using the platenSanding Workpiece Accessories Rotary Phase ConverterH2845 Cleaning Pads Maintenance GeneralSchedule Sanding Belts Air SystemDust and Water Traps Service Platen ServiceTable Calibration Tools Needed Qty Brake ServiceTo check the brake pads To replace the brake padsOscillation Timing To check the sanding belt oscillationTo set the correct amount of airflow through Page To adjust the oscillation speed Oscillation SpeedTable Parallelism To adjust the table parallelism To adjust the pressure rollersPressure Rollers To adjust either V-belt Belt AdjustmentAir System Diagram To remove the conveyor belt use and follow the steps below Conveyor Belt ReplacementPage To adjust the feed belt tension Feed Belt TensionFeed Belt Tracking Date Approximate Hours Of Use Maintenance Performed Maintenance LogMachine Operations TroubleshootingTion Control Panel Electrical Diagram Control Panel Component Locations G0445/G0582/G9962Z/9962ZX Wide Belt Sander Wiring Box Components G0445/G0582/G9962ZX Contactor Connection Wiring Diagram G9962Z 220V Single-PhaseWiring Box Components G9962Z S T 220V/440V 3-Phase General Electrical Diagram E R SG9962Z 220V Single-Phase Tool Box and Accessories Diagram Description Tool Box and Accessories Parts ListSanding Motor System Diagram FAN Cover Sanding Motor System Parts ListTable Lift System Diagram Motor Cover Table Lift System Parts ListConveyor System Diagram Conveyor System Parts List Feed, Drum, and Pressure Roller Diagram Feed, Drum, and Pressure Roller Parts List Sanding Drum and Platen System Diagram Bracket Female Sanding Drum, and Platen System Parts ListUpper Roller System Diagram Upper Roller System Parts List Cabinet Assembly Diagram Cabinet Assembly Parts List G0582 Main Electrical Panel and Controls DiagramConversion Relays Main Electrical Panel and Controls Parts ListBelt Oscillation System Diagram Belt Oscillation System Parts List Label Diagram Labels List Hardware Recognition Chart G0445/G0582/G9962Z/9962ZX Wide Belt Sander Warranty & Returns Comments Warranty CardPage Page Call Today For a Free Full Color Catalog