Grizzly 9962ZX, G9962Z, G0582, G0445 instruction manual Recommended Adjustments

Page 22

To start the machine:

1.Wear safety glasses and respirator at all times when running the machine!

2.Connect the machine to the power source.

3.Press the TABLE UP and TABLE DOWN keys. The table should go up and down smoothly.

Note: On 3-phase machines, make sure the table moves in the same direction as the but- ton description. If not, then the power needs to be disconnected and any two power wires need to be switched at the circuit breaker in the electrical box. If using a phase converter, switch the R and T wires.

4.Press the FEED BELT START and FEED BELT STOP buttons. The feed belt should start, run, and stop smoothly.

5.Press the SANDING BELT START and SANDING BELT STOP buttons. The sanding belt should start, run, and stop smoothly.

The machine should run smoothly, with little or no vibration or rubbing noises. Strange or unnatu- ral noises should be investigated and corrected before operating the machine further.

If the machine seems to be running correctly, let it run for a short time to ensure that the mov- ing parts are working properly with no excessive vibration. DO NOT operate the machine if prob- lems cannot be corrected.

If you cannot locate the source of unusual noises, refer to Troubleshooting, and feel free to con- tact our Technical Support Department at (570) 546-9663.

Recommended

Adjustments

For your convenience, the adjustments listed below have been performed at the factory and require no further adjustment. However, we rec- ommend that you verify that the adjustments are correct and to your satisfaction.

Recommended adjustment checklist: Table Calibration, Page 28. Feed Belt Tension, Page 38. Feed Belt Tracking, Page 38. Air System, Page 27. Oscillation Timing, Page 30. Oscillation Speed, Page 32. Pressure Rollers, Page 33. Table Parallelism, Page 32. V-Belt Adjustment, Page 34.

-20-

G0445/G0582/G9962Z/9962ZX Wide Belt Sander

Image 22
Contents Model Page Table of Contents Warranty & Returns Foreword IntroductionContact Info External Features FeaturesControl Panel Internal Features Machine Data Sheet G0445 Machine Data Sheet G0582 Machine Data Sheet G9962Z Machine Data Sheet G9962ZX Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wide Belt Sanders Extension Cords Circuit Requirements220V/440V Connection Grounding440V Connection Clean Up Site ConsiderationsAir Line Installation SetupBeginning Assembly SectionDust Collection Crate contents, see FigureInventory To hook up a dust collection systemTo install the sanding belt Sanding BeltPressure Roller Test Start Up Recommended Adjustments Choosing Sandpaper Operation SafetyOperations GritAdjusting Feed Rate Table MovementAmp Draw Meter Using the platen Platen AdjustmentSanding Workpiece Rotary Phase Converter AccessoriesH2845 Cleaning Pads General MaintenanceSchedule Air System Sanding BeltsDust and Water Traps Platen Service ServiceTable Calibration To check the brake pads Brake ServiceTools Needed Qty To replace the brake padsTo check the sanding belt oscillation Oscillation TimingTo set the correct amount of airflow through Page Oscillation Speed To adjust the oscillation speedTable Parallelism To adjust the pressure rollers To adjust the table parallelismPressure Rollers Belt Adjustment To adjust either V-beltAir System Diagram Conveyor Belt Replacement To remove the conveyor belt use and follow the steps belowPage Feed Belt Tension To adjust the feed belt tensionFeed Belt Tracking Maintenance Log Date Approximate Hours Of Use Maintenance PerformedTroubleshooting Machine OperationsTion Control Panel Electrical Diagram Control Panel Component Locations G0445/G0582/G9962Z/9962ZX Wide Belt Sander Wiring Box Components G0445/G0582/G9962ZX Connection Wiring Diagram G9962Z 220V Single-Phase ContactorWiring Box Components G9962Z S T 220V/440V 3-Phase General Electrical Diagram E R SG9962Z 220V Single-Phase Tool Box and Accessories Diagram Tool Box and Accessories Parts List DescriptionSanding Motor System Diagram Sanding Motor System Parts List FAN CoverTable Lift System Diagram Table Lift System Parts List Motor CoverConveyor System Diagram Conveyor System Parts List Feed, Drum, and Pressure Roller Diagram Feed, Drum, and Pressure Roller Parts List Sanding Drum and Platen System Diagram Sanding Drum, and Platen System Parts List Bracket FemaleUpper Roller System Diagram Upper Roller System Parts List Cabinet Assembly Diagram Cabinet Assembly Parts List Main Electrical Panel and Controls Diagram G0582Main Electrical Panel and Controls Parts List Conversion RelaysBelt Oscillation System Diagram Belt Oscillation System Parts List Label Diagram Labels List Hardware Recognition Chart G0445/G0582/G9962Z/9962ZX Wide Belt Sander Warranty & Returns Warranty Card CommentsPage Page Call Today For a Free Full Color Catalog