Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15V2 manual Lever for adjustment of cutting height, Seat, Fuelling, Presentation

Models: 15V2

1 52

Download 52 pages 29.65 Kb

Page 16

Lever for adjustment of cutting height

PRESENTATION

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to 9 different positions.

Unit with side or rear ejection	40-90 mm
	(1 9/16" - 3 9/16")
BioClip or Combi unit,	45-95 mm
	(1 3/4" - 3 3/4")

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

Move the lever, mounted under the frontedge of the seat, to the left. The seat can then be moved forwards or backwards to the required position.

Fuelling

The engine should be run on 87 octane (or higher) unleaded petrol/gasoline (no oil added). For more information about methanol and ethanol fuels, see “Technical Data”.

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1").

WARNING!

Petrol/gasoline is highly inflammable. Observe care and fill up with fuel outdoors (see safety instructions).

IMPORTANT INFORMATION

The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt.

Impaired cooling of the engine. Risk of major engine damage.

14 – English

Image 16

Husqvarna 15V2 manual Lever for adjustment of cutting height, Seat, Fuelling, Presentation

Contents

Operator´s manual RiderEnglish Svenska CONTENTS Operator’s Manual for Rider INTRODUCTION Dear customerTravel and transport on public roads TowingSerial number Good serviceINTRODUCTION EXPLANATION OF SYMBOLS SAFETY INSTRUCTIONS Safety instructionsGeneral use Read the operator’s manual before starting the machineKeep children away from the area to be mowed Personal protective equipmentSAFETY INSTRUCTIONS Never leave the machine unsupervised with theBe especially careful when driving on slopes Driving on slopesMow upwards and downwards on slopes, not sideways SAFETY INSTRUCTIONSMaintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsDo not smoke when carrying out maintenance SAFETY INSTRUCTIONSThe engine and the exhaust system become very hot during operation Risk of burn injuries if touchedRegularly clean grass, leaves and other debris from the machine TransportNever run the machine in an enclosed area SAFETY INSTRUCTIONSPresentation PRESENTATIONLocation of the controls Throttle control Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONBefore starting DRIVINGStarting the engine 6. Push the choke lever gradually forward when the engine has started DRIVINGDriving the machine DRIVINGCutting tips DRIVINGRelease lever Stopping the engineDRIVING MAINTENANCE Maintenance scheduleRemoving the machine hoods MAINTENANCEEngine hood Front hoodChecking and adjustment of the steering wires Adjusting the brakeMAINTENANCE Poorly adjusted brakes can result in reduced braking powerChecking and adjustment of the throttle wire Checking and adjusting the choke wireReplacing the fuel filter MAINTENANCEReplacing the air filter MAINTENANCECheck the level of the battery acid Ignition systemChecking of the fuel pump’s air filter MAINTENANCEMAINTENANCE Inspecting the safety system26 - English Main fuse Checking the tyre pressureChecking the engine’s cooling air intake Cooling air intakeMAINTENANCE Fitting the cutting unitObserve caution to avoid trapping your hand Removing the cutting unit Installing BioClipMAINTENANCE Checking and adjusting the cutting unit’s ground pressure MAINTENANCEAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belt MAINTENANCEMAINTENANCE 32 - EnglishMAINTENANCE MAINTENANCE Service position for the cutting unitPlacing in service position MAINTENANCE 5. Disengage the spring for the drive belt tensioning wheelMAINTENANCE 8. Lift off the drive belt 1. Then pull out the pinChecking the blades BioClipCombi Combi Cutting unit with rear ejection Cutting unit with side ejectionService position Replacing the break-pin BioClip 90, CombiRemoval of BioClip plug Combi Removal of BioClip plugLUBRICATION Checking the engine’s oil levelChanging the oil filter Changing the oilLUBRICATION Lubricating the belt adjuster Checking the transmission’s oil levelGeneral lubrication LUBRICATIONProblem TROUBLE SHOOTING SCHEDULEProcedure Service STORAGEWinter storage CoverTECHNICAL DATA DimensionsRider EngineEU declaration of conformity Only applies to Europe SERVICE JOURNAL Pre-delivery serviceSERVICE JOURNAL Work doneDate, mileage, stamp, sign English´z+H-¶6-¨ SERVICE JOURNALPage ´z+H-¶6-¨ 2002W45 114