Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15V2 manual Stopping the engine, Release lever, Driving

Models: 15V2

1 52

Download 52 pages 29.65 Kb

Page 21

Image 21

DRIVING

WARNING!

Never drive the machine on ground with a slope of more than 15°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction.

MAX 15

Stopping the engine

Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard. Avoid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs.

1.Lift up the cutting unit by pulling the lever back to the locked position.

2.Move the throttle control to the MIN. position. Turn the ignition key to the STOP.

3. When the Rider is at a standstill, press down the

parking brake and push in the locking button.

Release lever

The release control must be pulled out in order for the Rider to be moved when the engine is shutoff.

English – 19

Page 21

Image 21

Husqvarna 15V2 manual Stopping the engine, Release lever, Driving

Contents

Rider Operator´s manualEnglish Svenska CONTENTS Operator’s Manual for Rider Dear customer INTRODUCTIONTravel and transport on public roads TowingGood service Serial numberINTRODUCTION EXPLANATION OF SYMBOLS Safety instructions SAFETY INSTRUCTIONSGeneral use Read the operator’s manual before starting the machinePersonal protective equipment Keep children away from the area to be mowedSAFETY INSTRUCTIONS Never leave the machine unsupervised with theDriving on slopes Be especially careful when driving on slopesMow upwards and downwards on slopes, not sideways SAFETY INSTRUCTIONSChildren MaintenanceNever allow children to operate the machine Never fill the fuel tank indoorsSAFETY INSTRUCTIONS Do not smoke when carrying out maintenanceThe engine and the exhaust system become very hot during operation Risk of burn injuries if touchedTransport Regularly clean grass, leaves and other debris from the machineNever run the machine in an enclosed area SAFETY INSTRUCTIONSPRESENTATION PresentationLocation of the controls Choke lever Throttle controlSpeed limiter Parking brakeLift lever for cutting unit Cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionSeat Lever for adjustment of cutting heightFuelling PRESENTATIONDRIVING Before startingStarting the engine DRIVING 6. Push the choke lever gradually forward when the engine has startedDRIVING Driving the machineDRIVING Cutting tipsStopping the engine Release leverDRIVING Maintenance schedule MAINTENANCEMAINTENANCE Removing the machine hoodsEngine hood Front hoodAdjusting the brake Checking and adjustment of the steering wiresMAINTENANCE Poorly adjusted brakes can result in reduced braking powerChecking and adjusting the choke wire Checking and adjustment of the throttle wireReplacing the fuel filter MAINTENANCEMAINTENANCE Replacing the air filterIgnition system Check the level of the battery acidChecking of the fuel pump’s air filter MAINTENANCEInspecting the safety system MAINTENANCE26 - English Checking the tyre pressure Main fuseChecking the engine’s cooling air intake Cooling air intakeFitting the cutting unit MAINTENANCEObserve caution to avoid trapping your hand Installing BioClip Removing the cutting unitMAINTENANCE MAINTENANCE Checking and adjusting the cutting unit’s ground pressureChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitReplacing the cutting unit belt MAINTENANCE32 - English MAINTENANCEMAINTENANCE Service position for the cutting unit MAINTENANCEPlacing in service position 5. Disengage the spring for the drive belt tensioning wheel MAINTENANCE8. Lift off the drive belt 1. Then pull out the pin MAINTENANCEBioClip Checking the bladesCombi Combi Cutting unit with rear ejection Cutting unit with side ejectionReplacing the break-pin BioClip 90, Combi Service positionRemoval of BioClip plug Combi Removal of BioClip plugChecking the engine’s oil level LUBRICATIONChanging the oil Changing the oil filterLUBRICATION Checking the transmission’s oil level Lubricating the belt adjusterGeneral lubrication LUBRICATIONTROUBLE SHOOTING SCHEDULE ProblemProcedure STORAGE ServiceWinter storage CoverDimensions TECHNICAL DATARider EngineEU declaration of conformity Only applies to Europe Pre-delivery service SERVICE JOURNALWork done SERVICE JOURNALDate, mileage, stamp, sign EnglishSERVICE JOURNAL ´z+H-¶6-¨Page 114 ´z+H-¶6-¨ 2002W45