Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15V2 manual Service Journal, Pre-delivery service

Models: 15V2

1 52

Download 52 pages 29.65 Kb

Page 48

SERVICE JOURNAL

SERVICE JOURNAL

Work done

Date, mileage, stamp, sign

Pre-delivery service

1.	Top up battery with acid and recharge for four hours.
2.	Fit steering wheel, seat and any optional equipment.
3.	Adjust cutting unit:
	Adjust the lifting springs (the “weight” of the cutting unit should
	be 12-15 kg/26,5-33 lbs). Applies to BioClip and Combi deck.
	Adjust cutting unit so that rear edge is about 2–4 mm/1/8"
	higher than front edge.
	Adjust cutting unit height setting so that cutting height limit is
	5 mm/3/16" above the frame of the unit at the lowest cutting
	height.
4.	Check that engine has correct amount of oil.
5.	Check that the right amount of oil is in the transmission.
6.	Check and adjust tyre pressure (60 kPa/0.6 bar/8.5 PSI).
7.	Connect battery.
8.	Fill with fuel and start engine.
9.	Check that machine does not move in neutral.
10. Check:
	Forward drive.
	Reverse drive.
	Operation of blades.
	Seat safety switch.
	Lift lever safety switch.
	Safety switch for the hydrostat pedals.
11. Check engine revs 2 900±100rpm.
12. Tell customer about:		Pre-delivery service carried out.
		Pre-delivery service carried out.
	Need and benefits of following the service schedule.	No outstanding problems.
		No outstanding problems.
	The need and advantages of leaving the machine for regular	Certified:
	service.
	The effects of maintenance on the machine’s second hand
	value.
	Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 8 hours 1. Change engine oil.

46 – English

Image 48

Husqvarna 15V2 manual Service Journal, Pre-delivery service

Contents

Rider Operator´s manualEnglish Svenska CONTENTS Operator’s Manual for Rider INTRODUCTION Dear customerTravel and transport on public roads TowingGood service Serial numberINTRODUCTION EXPLANATION OF SYMBOLS SAFETY INSTRUCTIONS Safety instructionsGeneral use Read the operator’s manual before starting the machineKeep children away from the area to be mowed Personal protective equipmentSAFETY INSTRUCTIONS Never leave the machine unsupervised with theBe especially careful when driving on slopes Driving on slopesMow upwards and downwards on slopes, not sideways SAFETY INSTRUCTIONSMaintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsDo not smoke when carrying out maintenance SAFETY INSTRUCTIONSThe engine and the exhaust system become very hot during operation Risk of burn injuries if touchedRegularly clean grass, leaves and other debris from the machine TransportNever run the machine in an enclosed area SAFETY INSTRUCTIONSPRESENTATION PresentationLocation of the controls Throttle control Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONDRIVING Before startingStarting the engine 6. Push the choke lever gradually forward when the engine has started DRIVINGDriving the machine DRIVINGCutting tips DRIVINGStopping the engine Release leverDRIVING MAINTENANCE Maintenance scheduleRemoving the machine hoods MAINTENANCEEngine hood Front hoodChecking and adjustment of the steering wires Adjusting the brakeMAINTENANCE Poorly adjusted brakes can result in reduced braking powerChecking and adjustment of the throttle wire Checking and adjusting the choke wireReplacing the fuel filter MAINTENANCEReplacing the air filter MAINTENANCECheck the level of the battery acid Ignition systemChecking of the fuel pump’s air filter MAINTENANCEInspecting the safety system MAINTENANCE26 - English Main fuse Checking the tyre pressureChecking the engine’s cooling air intake Cooling air intakeFitting the cutting unit MAINTENANCEObserve caution to avoid trapping your hand Installing BioClip Removing the cutting unitMAINTENANCE Checking and adjusting the cutting unit’s ground pressure MAINTENANCEAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belt MAINTENANCEMAINTENANCE 32 - EnglishMAINTENANCE Service position for the cutting unit MAINTENANCEPlacing in service position MAINTENANCE 5. Disengage the spring for the drive belt tensioning wheelMAINTENANCE 8. Lift off the drive belt 1. Then pull out the pinChecking the blades BioClipCombi Combi Cutting unit with rear ejection Cutting unit with side ejectionService position Replacing the break-pin BioClip 90, CombiRemoval of BioClip plug Combi Removal of BioClip plugLUBRICATION Checking the engine’s oil levelChanging the oil Changing the oil filterLUBRICATION Lubricating the belt adjuster Checking the transmission’s oil levelGeneral lubrication LUBRICATIONTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage CoverTECHNICAL DATA DimensionsRider EngineEU declaration of conformity Only applies to Europe SERVICE JOURNAL Pre-delivery serviceSERVICE JOURNAL Work doneDate, mileage, stamp, sign English´z+H-¶6-¨ SERVICE JOURNALPage ´z+H-¶6-¨ 2002W45 114