Schumacher SC-200A, SCF-200A Operating Instructions, Maintenance Instructions, Charging, Charged

Page 3

11.2LED Display

CHECK BATTERY (red) LED lit: Indicates the battery is not properly connected to the charger.

CHECK BATTERY (red) LED blinking: Indicates the charger is in abort mode.

CHARGING

(yellow) LED lit: Indicates the charger is charging the

battery.

 

CHARGED

(green) LED lit: Indicates the battery is fully charged and the

charger is in maintain mode.

NOTE: See the Operating Instructions section for a complete description of the charger modes.

12.OPERATING INSTRUCTIONS

Charging

1.Ensure that all of the charger components are in place and in good working condition, including the plastic boots on the battery clips.

2.Connect the battery following the connection instructions described in Using the Quick-Disconnect Cable Connectors section.

3.Set the Amp/Volt Selector Switch to the proper setting for the battery being charged.

4.Connect the AC power following the precautions listed in Section 8.

5. If you’ve connected everything correctly, the CHARGING (yellow) LED should be lit indicating that the charger is charging. If the CHARG-

ING (yellow) LED does not light or if the CHECK BATTERY (red) LED is lit, check the connections or have the battery checked/ replaced.

NOTE: This charger is equipped with an auto-start feature. It will not supply current to the battery clips until a battery is properly connected. Unlike tradi- tional chargers, the clips will not spark if touched together.

USING THE QUICK-DISCONNECT CABLE CONNECTORS

Connect any of the three output cable assemblies to the charger in seconds. Make sure to place the charger on a dry, non-flammable surface like metal or concrete.

NOTE: Never connect the clamp and ring terminal connectors together for use in other applications, such as external battery or other power source charging, or to extend the output cable length, as reverse polarity and/or overcharge conditions will occur.

50 amp Battery Clips

1.Connect the end of the 50 amp battery clips cable Quick-Connect to the charger.

2.Follow the steps in sections 6 and 7 to connect the output clips to the battery.

3.After a good electrical connection is made to the battery, plug the power cord into a 3-prong grounded 120V AC electrical wall outlet. Make sure to place the charger on a dry, non-flammable surface like metal or concrete.

Permanent Ring Connectors

The ring connectors permanently attach to the battery providing easy access to quickly charge your battery. This application is appropriate for motorcycles, lawn tractors, ATVs and snowmobiles.

1.To permanently attach to a battery, loosen and remove each nut from the bolt at the battery terminal.

2.Connect the red POSITIVE ring connector ring to the POSITIVE battery terminal.

3.Connect the black NEGATIVE connector ring to the NEGATIVE battery terminal.

4.Replace and tighten the nuts to secure.

5.Connect the end of the ring terminal cable Quick-Connect to the char- ger. Take care to keep the wires and plug away from metal and moving parts.

6.Plug the charger power cord into a 3-prong grounded 120V AC electrical wall outlet. Make sure to place the charger on a dry, non-flammable surface like metal or concrete.

12V Accessory Plug

Charge or maintain your battery without lifting the hood.

1.Connect the end of the 12V Accessory Plug Cable Quick-Connect to the charger.

2.Insert the 12V accessory plug into the 12V accessory outlet.

3.Route the power cord from charger through the vehicle’s open window.

4.Plug the charger power cord into a 3-prong grounded 120V AC electrical wall outlet. Make sure to place the charger on a dry, non-flammable surface like metal or concrete.

Battery Connection Indicator

If the charger does not detect a properly connected battery, the CHECK BAT-

TERY (red) LED will light continuously until such a battery is detected.

Charging will not begin while the CHECK BATTERY (red) LED is on..

Completion of Charge

 

Charge completion is indicated by the CHARGED

(green) LED. When

lit, the charger has stopped charging and switched to the Maintain Mode of operation.

Maintain Mode (Float-Mode Monitoring)

When the CHARGED (green) LED is lit, the charger has started Maintain Mode. In this mode, the charger keeps the battery fully charged by delivering a small current when necessary. If the battery voltage drops below a preset level, the charger will go back into Charge Mode until the battery voltage returns to the full charge level, at which point the charger will return to Maintain Mode. The voltage is maintained at a level determined by the 6 volt or 12 volt battery type selected.

NOTE: The charger automatically switches between Charge Mode and

Maintain Mode as necessary. The CHARGED (green) LED will cycle on

when the battery is at full charge and off when the voltage drops below a preset level and the charger goes into Charge Mode. This cycle will continue, and the

CHARGED (green) LED will stay on for longer periods of time as the bat- tery becomes more fully charged.

Desulfation Mode

If the battery is left discharged for an extended period of time, it could become sulfated and not accept a normal charge. If the charger detects a sulfated battery, the charger will switch to a special mode of operation designed for such batteries. If successful, normal charging will resume after the battery is desulfated. Desulfation could take up to 8 hours. If desulfation fails, charging

will abort and the CHECK BATTERY (red) LED will blink.

Aborted Charge

If charging can not be completed normally, charging will abort. When charging

aborts, the charger’s output is shut off, and the CHECK BATTERY (red) LED will blink. To reset after an aborted charge, either disconnect the battery or unplug the charger.

13.CALCULATING charge times

This charger adjusts the charging time in order to charge the battery com- pletely, efficiently and safely.

This battery charger has a rated output of 2 and 4 amperes. This output will vary with the age and condition of the battery being charged. If the battery has only been slightly discharged, it can be charged in less than a few hours. The same battery will take longer to charge if it is very weak.

13.1Charging Times

 

Battery Condition

2 Amp, 12 Volt Battery

50% Discharged

100% Discharged

Ampere Hour Battery Capacity

Approximate Average Charge Time in Hours

 

 

 

10

3.2

6.2

 

 

 

12

4.0

7.5

 

 

 

20

6.4

12.4

 

 

 

 

Battery Condition

 

 

 

 

 

4 Amp, 6 Volt Battery

50% Discharged

100%

Discharged

 

 

 

Ampere Hour Battery Capacity

Approximate Average Charge Time in Hours

 

 

 

 

10

1.6

 

3.2

 

 

 

 

12

2.0

 

4.0

 

 

 

 

20

3.2

 

6.4

 

 

 

 

14.MAINTENANCE INSTRUCTIONS

14.1Before performing maintenance, unplug and disconnect the battery charger

(see Sections 6, 7 and 8).

14.2After use, unplug the charger and use a dry cloth to wipe all battery corro- sion and other dirt or oil from the terminals, cords, and the charger case.

14.3Ensure that all of the charger components are in place, securely attached and in good working condition, including the plastic boots on the battery clips.

14.4Servicing does not require opening the unit, as there are no user-service- able parts.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Risk of electric shock or fire Important Safety InstructionsPersonal Precautions Preparing to ChargeFeatures DC Connection PrecautionsFollow These Steps When Battery is Installed in Vehicle Battery Charging AC ConnectionsCharging Maintenance InstructionsUsing the QUICK-DISCONNECT Cable Connectors Operating InstructionsStorage Instructions TroubleshootingReplacement Parts Limited WarrantyUbicación DEL Cargador Instrucciones Importantes DE SeguridadPrecauciones Personales Preparación Para LA CargaCarga DE BATERÍA, Conexiones DE CA CaracterísticasSiga Estos Pasos Cuando LA Batería SE Encuentre Fuera DEL Vehículo13. Cálculo DEL Tiempo DE Carga Instrucciones DE MantenimientoInstrucciones DE Almacenaje Repuestos Localización Y Solución DE ProblemasProblema Posible Causa Solución Antes DE Devolver a ReparacionesRisque de choc électrique ou d’incendie Consignes DE Sécurité ImportantesPrécautions Personnelles Préparation Pour LE ChargementCaractéristiques Emplacement DU ChargeurPrécautions SUR LA Connexion C.C Chargement D’UNE Batterie Raccordements C.ACalcul DU Temps DE Charge Directives DE MontagePanneau DE Contrôle Consignes D’UTILISATION18. Pièces DE Rechange Consignes D’ENTRETIENDirectives D’ENTREPOSAGE Avant DE L’ENVOYER Pour Réparation

SCF-200A, SC-200A specifications

The Schumacher SC-200A and SCF-200A are two highly regarded battery chargers that cater to a variety of charging needs. Renowned for their reliability and efficiency, these models have become popular among automotive enthusiasts and professionals alike.

Starting with the SC-200A, this model stands out for its high output of 200 amps, making it suitable for charging both standard and larger capacity batteries. It features a smart microprocessor-controlled charging system that automatically adjusts the charging current based on the battery's state. This technology ensures optimal charging without the risk of overcharging, thus enhancing battery lifespan.

One of the key features of the SC-200A is its versatility. It is designed to work with a range of battery types, including lead-acid and AGM batteries, making it a go-to option for users with different vehicle types. The charger is also equipped with multi-stage charging capabilities, which provide a more thorough and careful charging process. The intuitive LED display provides clear information on the charging status, ensuring users are always informed about the health of their battery.

The SCF-200A, on the other hand, brings several advanced features to the table. This model focuses on fast charging, streamlining the process without sacrificing safety. With a 200-amp starting power, it is capable of jump-starting vehicles with larger engines with ease. Its heavy-duty clamps and rugged design make it suitable for harsh working conditions, promising durability and performance.

A notable characteristic of the SCF-200A is its integrated safety features. It includes reverse polarity protection, ensuring that incorrect connections do not lead to potential damage. Additionally, the unit has temperature regulation, which prevents overheating during extended charging sessions.

Both models are built with user-friendly interfaces, making them ideal for both novices and experienced users. They emphasize safety and efficiency, positioning them as substantial tools in automotive care.

In conclusion, the Schumacher SC-200A and SCF-200A are exemplary battery chargers that embody essential features such as smart charging technology, versatility, rapid charging capabilities, and robust safety measures. They are thoughtfully designed to meet the diverse needs of users, making them valuable assets for those looking to maintain their vehicle's battery with confidence.
Top Page Image Contents