Ingersoll-Rand 5212-15, 7015-11, 5213-1B manual Short Grinder, M10, Released, 2884-2

Page 1

OPERATOR’S

MANUAL

SECTION

M10

MANUAL

16

INCLUDING: OPERATION,INSTALLATION& MAINTENANCE

Released:

2/86

Tool Products

 

 

Revised:

1-20-95

“0” SERIES

DIE GRINDER

(SHORT GRINDER)

Form:

2884-2

 

Models:

7015-11-(), 8212-1B-( ) and 8213-1B.

 

 

WARNING

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

FAILURE TO OBSERVE THE FOLLOWING

To aid the operator’s understanding of proper and safe use of grinders, the publications, “Use, Care and Protection of Abrasive Wheels”, A.N.S.I. 87.1, and “Safety Code for Portable Air Tools”, A.N.S.I. 8186.1, can be purchased from:

American National Standards Institute, Inc.

1430 Broadway

New York, New York 10018

WARNINGS COULD RESULT IN INJURY.

lUse only medium and high strength mounted wheels.

lDo not use excessive work pressure.

lAllow only people who have received training in “propergrind-

er operation” to operate grinder.

lDo not remove any labels. Replace any damaged label. l Use only accessories recommended by ARO.

l

l

l

l

l l l

l

l l

l

Operate this tool at 90 p.s.i.g. (6.2 bar) maximum air pressure at the air inlet of the tool.

Disconnect air supply from tool before removing/installing mounted wheel, mounted stone or performing other mainte- nance procedures.

Keep hands, clothing and long hair away from rotating end of tool.

Anticipate and be alert for sudden changes in motion during start up and operation of any power tool.

Never exceed rated r.p.m. of tool.

Wear suitable eye and hearing protection while operating tool. Tool shaft can continue to rotate briefly after throttle is re- leased.

Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.

Use tool only for purposes for which it was intended.

Never use mounted stone or carbide burr with speed rating lower than r.p.m. rating of tool.

Use only mounted wheels of the A, B and W shapes.

Repeated prolonged operator exposure to vibrations which may be generated in the use of certain hand-held tools may produce Raynaud’s phenomenon, commonly referred to as Whitefinger disease. The phenomenon produces numbness and burning sensations in the hand and may cause circulation and nerve dam- age as well as tissue necrosis. Repetitive users of hand-held tools who experience vibrations should closely monitor duration of use and their physical condition.

The use of other than genuine ARO replacement parts may result in safety hazards, decreased tool performance and in- creased maintenance and may invalidate all warranties.

ARO is not responsible for customer modification of tools for applications on which ARO was not consulted.

Tool maintenance and repair should be performed by autho- rized, trained, competent personnel. Consult your nearest ARO authorized servicenter.

It is the responsibility of the employer to place the information in this manual into the hands of the operator.

For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand Distribution Center, White House, TN at PH: (615) 672-0321, FAX: (615) 672-0601.

ARO Tool Products

Ingersoll-Rand Company

1725 U.S. No. 1 North l P.O. Box 8000 l Southern Pines, NC 28388-8000

01995 THE ARO CORPORATION . PRINTED IN USA.

Part of worldwide Ingersoll-Rand

Image 1
Contents M10 Short GrinderReleased 2884-2Operating or performing Wear eye protectionNON-EU Models AIR Supply Requirements Routine Lubrication RequirementsRecommended Lubricants Mounting Instructions29j-27 Items Included in Service KIT no13M10 ServicePart Number for Ordering Throttle Assembly DISASSEMBLY/ASSEMBLY InstructionsMotor Disassembly Motor AssemblyPart of Worldwide Ingersoll-Rand

5213-1B, 5212-15, 7015-11 specifications

Ingersoll-Rand is a well-respected name in the industrial equipment sector, known for its commitment to quality, innovation, and reliability. Among its product offerings, the Ingersoll-Rand 7015-11, 5212-15, and 5213-1B models stand out for their exceptional performance and advanced technology.

The Ingersoll-Rand 7015-11 model is built to enhance operational efficiency and productivity. One of its key features is its powerful air compressor system, which delivers high output while maintaining low energy consumption. With a robust design, it is engineered for durability and longevity, making it suitable for various industrial applications. Additionally, it is equipped with advanced noise-reduction technology, which significantly lowers operational noise levels, creating a more favorable working environment.

Moving to the Ingersoll-Rand 5212-15, this model is designed for excellent versatility. It features a compact and lightweight design, making it easy to transport and maneuver in tight spaces. The model is also equipped with a user-friendly digital display for monitoring performance metrics in real-time, allowing users to optimize operation and maintenance schedules effectively. Enhanced safety features such as overload protection and automatic shut-off mechanisms ensure operation within safe parameters, mitigating risks associated with heavy-duty industrial tasks.

Lastly, the Ingersoll-Rand 5213-1B embodies a commitment to advanced technology and user-friendly design. One of its standout characteristics is the integrated IoT capabilities that enable remote monitoring of system performance. This connectivity allows businesses to track efficiency, perform predictive maintenance, and minimize downtime. The 5213-1B also boasts high energy efficiency ratings, which help in reducing operational costs over time.

Overall, the Ingersoll-Rand 7015-11, 5212-15, and 5213-1B models are exceptional choices for businesses looking to enhance their productivity through reliable and innovative technology. Each model integrates cutting-edge features designed to meet the demanding needs of modern industries, ensuring that they deliver consistent performance for years to come. With a focus on quality and customer satisfaction, Ingersoll-Rand continues to set the standard in the market for air-compressing and industrial equipment.