Harbor Freight Tools 93808 operating instructions Operation, Installing Cutting Blade

Page 11

OPERATION

Install the Saw Blade. Prepare and secure the material to be cut before turning on saw. The Battery (H) should have a full charge before using saw. Remove battery before making any adjustments. Refer to Figure 3, on page 18.

INSTALLING CUTTING BLADE

NOTE: The Lock Bolt is a reverse thread.

1.Remove The Battery (O) before making any adjustments.

2.Press on the Spindle Lock Button (J) to keep the Saw Blade from moving while turning the Blade Bolt (I).

3.Using the Hex Key (P), loosen and remove Lock Bolt (I) and Outer Flange (I).

4.Rotate the Lower Blade Guard (K), counterclockwise to allow entry of the Saw Blade.

5.Insert Saw Blade through the Base Plate (M) until blade fits on the motor spindle.

Notice the arrow on the Lower Blade Guard (K) and the arrow on the Saw Blade. They should be pointing in the same direction.

6.Replace the Outer Flange (I) and Blade Bolt (I). Tighten with the Hex Key (P) while pressing on the Spindle Lock Button (J). Verify that the Spindle Lock Button (J) is in the up (unlocked) position.

7.Replace the Hex Key (P) to its storage hole in the housing of the saw.

ADJUSTING THE SAW PRIOR TO CUTTING

1.To adjust the angle of blade, loosen the Bevel Cut Adjustment Knob (G) and move Base Plate (M) while observing the degree scale located next to the Bevel Cut Adjustment Knob (G).

2.To adjust the depth of the cut, loosen the Depth Adjustment Knob (N), which is located next to the motor housing, and move the Base Plate (M) while observing the amount of Saw Blade exposed under Base Plate. Tighten the Depth Adjustment Knob (N) after making the adjustment.

3.Rip Fence installation and adjustment:

The Rip Fence can be inserted into either the left or right side at the toe of the Base Plate (M). Insert the Rip Fence into the fence guides until it contacts the Retention Bolt (Q). Loosen the Retention Bolt (Q) until the fence can slide through then secure it by turning the Retention Bolt (Q) clockwise. The Rip Fence is adjustable from 0”- 5”. ( Refer to Page 18, Fig. 3)

Page 11

SKU 93808 For technical questions, please call 1-800-444-3353.

English

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Cordless 18V Circular SAW With Laser Work Area Product SpecificationsGeneral Safety Rules for ALL Battery Operatedtools Save this ManualTool USE and Care Electrical SafetyPersonal Safety Service Kickback Specific Safety RulesCauses and Operator Prevention of Kickback Symbology Battery Precautions Unpacking Never charge the Battery H more than two hours continuouslyInstalling & Removing the Battery Pack Charging BatteryWork Light and Laser Guide Operation Installing Cutting BladeAdjusting the SAW Prior to Cutting Functions Cutting Prepare Material Before CuttingPlease Read the Following Carefully INSPECTION, MAINTENANCE, and CleaningPart Description Qty Parts ListAssembly Diagram Prévenir LA Blessure Sérieuse Sans Cordon 18V LE Scier Circulaire Avec LE LaserConservez CES Instructions Spécifications DE ProduitSauvez CE Manuel Sécuritéélectrique Réparation Règles de Sécurité Particulières Causes du retour d’outil et prévention par l’utilisateur Modèle SymbologyPrécautions DE Batterie Défaisant Le fait de Charger la Batterie Travaillez LE Guide Clair ET À Laser LE Fait D’INSTALLER LA Lame CoupanteOpération LE Réglage DU Scier Avant LA Coupure Installation de Clôture d’Accroc et ajustageChiffre Coupure Préparez LA Matière Avant LA CoupureLisez S’IL Vous Plaît LE Suivant Soigneusement ’INSPECTION, LA Maintenance ET LE NettoyagePart Description Qty Liste DE PartiesDiagramme D’ASSEMBLAGE
Top Page Image Contents