Harbor Freight Tools 93808 operating instructions Specific Safety Rules, Kickback

Page 5

SPECIFIC SAFETY RULES

1.DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards. (See

KICKBACK)

Do not reach underneath the work. The guard can not protect you from the blade below the work.

2.Check lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the Retracting Handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

3.Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

4.Lower guard should be retracted manually only for special cuts such as “Pocket Cuts”and “Compound Cuts.” Raise lower guard by Retracting Handle. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower guard should operate automatically.

5.Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

6.NEVER hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.

7.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.

8.When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding.

9.Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

SKU 93808 For technical questions, please call 1-800-444-3353.

Page 5

English

Image 5
Contents Cordless 18V Circular SAW With Laser General Safety Rules for ALL Battery Operatedtools Product SpecificationsSave this Manual Work AreaTool USE and Care Electrical SafetyPersonal Safety Service Kickback Specific Safety RulesCauses and Operator Prevention of Kickback Symbology Battery Precautions Unpacking Never charge the Battery H more than two hours continuouslyInstalling & Removing the Battery Pack Charging BatteryWork Light and Laser Guide Operation Installing Cutting BladeAdjusting the SAW Prior to Cutting Functions Cutting Prepare Material Before CuttingPlease Read the Following Carefully INSPECTION, MAINTENANCE, and CleaningPart Description Qty Parts ListAssembly Diagram Prévenir LA Blessure Sérieuse Sans Cordon 18V LE Scier Circulaire Avec LE LaserConservez CES Instructions Spécifications DE ProduitSauvez CE Manuel Sécuritéélectrique Réparation Règles de Sécurité Particulières Causes du retour d’outil et prévention par l’utilisateur Modèle SymbologyPrécautions DE Batterie Défaisant Le fait de Charger la Batterie Travaillez LE Guide Clair ET À Laser LE Fait D’INSTALLER LA Lame CoupanteOpération LE Réglage DU Scier Avant LA Coupure Installation de Clôture d’Accroc et ajustageChiffre Coupure Préparez LA Matière Avant LA CoupureLisez S’IL Vous Plaît LE Suivant Soigneusement ’INSPECTION, LA Maintenance ET LE NettoyagePart Description Qty Liste DE PartiesDiagramme D’ASSEMBLAGE