Craftsman 973.111430 II Keep Handles DRY, CLEAN, and Free, Important Safety Rules for Battery

Page 4

10/03/01 WED 13:44

FAX 864 964 3314 RYOBI CUSTOMER SERVICE

_005/015

RULES FOR SAFE OPERATION (Continued)

NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite flam- mable liquids, gases, or fumes.

IIKEEP HANDLES DRY, CLEAN, AND FREE

FROM OIL AND GREASE. Always Use a clean cloth when cleaning. Never use brake fluids,

gasoline, petroleum-based productsor any strong solvents to clean yourtool.

STAY ALERT. Watch whet you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

M CHECK DAMAGED PARTS. Beforefurther use of

the tool, a guard or other part that Is damaged should be carefully checked to determine that itwill operate properly and perform its intendedfunction. Check for alignment of moving parts, bindingof moving parts, breakage of parts, mounting,and any other conditionsthat may affect its operation.

A guard or other part that is damaged shouldbe properly repaired or replaced by an authorized service center unless indicated elsewhere in this instructionmanual.

DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

DRUGS, ALCOHOL, MEDICATION. Do not

operate tool while under the influenceof drugs, eTcehof,or any medication.

DRILLING OR DRIVING SCREWS INTO

ELECTRICAL WIRING IN WALLS_ CEILINGS, OR OTHER AREAS CAN CAUSE THE BIT OR

CHUCK TO BECOME ELECTRICALLY LIVE. 0o not touch metal parts when drilling; grasp only the Insulmed handle(s) or plastic housing when using this tool. Make sure hidden electrical wiring, water

pipes, and mechanical hazards are not in the path of the bit when ddlling Into a wall.

[] INSPECT FOR and remove all nailsfrom lumber

before drilling.

IMPORTANT SAFETY RULES FOR BATTERY

TOOLS

Battery tools do not have to be plugged into an electrical outlet: therefore, they are always in operating condition. Be aware of possible hazards

when not using your battery tool or when changing acoeesodes,

USE ONLY THE CHARGER PROVIDED WITH YOUR BATTERY TOOL. Do not substitute any other charger. Use of another charger could cause batteries to explode causing possible serious injury.

IIDO NOT PLACE BATTERY TOOLS OR THEIR

BATTERIES NEAR FIRE OR HE_.T. They may explode.

DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION.

IIIYour battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F,

MUnder extreme usage or temperature conditions, battery leakage may occur. If liquidcomes in contact with yourskin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets in youreyes, flush them with clean water for at least 10 minutes, then seek immediate medical attantian.

MIf carryingyour battery tool at your side, make sure it is not running and yourfinger is not on the switch.Avoid accidental starting,

IISECURE WORK before applyingpower. NEVER hold work,piece in your hand or across your legs.

WHEN SERVICING USE ONLY IDENTICAL

CRAFTSMAN REPLACEMENT PARTS.

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

SAVE THESE INSTRUCTIONS. This manual

contains importantsafety and operating instructionsfor charger item number 9-11049 (1421410).

Before using battery charger, read all instructions and cautionary markings In this manual, on battery charger, and product using battery charger.

_WARNING; To reduce dsk of injury,charge only nickel-cadmiumtype rechargeabtebatteries. Other types of batteries may burstcausing personal injuryand damage,

[] Do not expose charger to rain or snow.

[] Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electricshock, or injuryto persons.

[] To reduce risk of damage to charger body and cord, pull by plug body ratherthan cord when disconnectingcharger.

Make sure cord Is located so that it will not be stepped on, Idpped over, or otherwise subjected to damage or stress.

4

Image 4
Contents Model No Specifications IIIMeaning Safety Alert Symbol Read ALL InstructionsII Keep Handles DRY, CLEAN, and Free Important Safety Rules for BatteryII do not Place Battery Tools or Their Do not Charge Battery Tool in a Damp or WET LocationDo not Operate Charger with a See Fum See Fi#umCharging BAI-FERY Pack To ChargeSee Figure Selector Variable SpeedSos Figure To Remove Baitery PackSwitch Lock LockTrigger Keyless Chuck DrillbitSee FTgure7 See Fi#ure ZBIT Storage BitstorageareaLevel Drilling DrillingChuck Removal Gee Figures f3, 14,CHUCK,JAWSHEXKEY Wrengh To Retighten a Loose ChuckBatteries Preparation for RecyclingParts List See Back page for Parts Ordering Instructions