Clarity 87392-11 manual Clarity User Guide, March 1, 2011 Rev

Page 33

On the Calibration screen under Step 4 (See Fig. 4.1), there are six parameters that describe the lens that will be analyzed:

1.Diameter

2.Index of Refraction

3.Power

4.Front Curve

5.Back Curve

6.Center Thickness

These parameters are for both the plus and the minus lenses.

NOTE

If these lenses are misplaced or compromised in any way, please call the factory and order a new calibration lens. Once the new lens arrives, check these parameters and make any necessary changes.

To perform this calibration, select the Calibrate button. You will be prompted to remove the lens. Make sure there is no lens in the chamber and select OK. After 25 seconds, you will be prompted to insert the calibration lens. Put the -6.00 lens in the chamber and select OK. The Clarity will analyze the lens and will instruct you to place the +6.00 lens in the chamber.

Select OK.

After both lenses are analyzed, the plus and minus slope adjustments will be displayed. Select YES to accept these changes. The calibration wizard will appear telling you that the power calibration is complete. Select OK. To exit back to the Job screen, select OK at the bottom of the screen and then on the next screen select Next.

NOTE

On this screen, there is also a Power Offset box. This can be used if you see a consistent power error. For example, powers are showing 0.25 weak across the board. Enter a +.25 and all analyzed powers will have 0.25 added to the final reading. This functions like the manual eyepiece adjustment for power on a conventional lensometer.

This screen includes two parameters labeled Minus Prism Bias and Plus Prism Bias. They are constants and should not be changed unless directed by the factory.

To verify power calibration, there is an internal job (Job Number 999999999) which will allow you to use the two calibration lenses (+6 and -6). From the main Job screen enter the Job Number 999999999 and follow the directions. Each lens will show the measured power in the upper right hand corner of the screen. If they are within acceptable limits, you can move on. If they are out of tolerance, recalibrate.

Clarity User Guide, March 1, 2011 - Rev. 1.06

Page 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Clarity User Guide Safety Reminders Table of Contents Home Burn Distance, Near and Prism Power Checks Unpacking the Clarity Getting Started1a Block #1 P/N 33593 Bottom Shipping Block Foam Shipping Blocks in the Blocking Chamber1c Shipping Bracket Assembly, Clarity P/N 1d Installed Shipping Bracket Assembly Clarity Front View User Items Clarity Rear Connector Bulkhead Installing the Glass Plate This page intentionally left blank for duplexing purposes Powering on the Clarity Basic OperationEstablishing Communications Keep hands away from unit during the blocking function Touch Screen Display and Job ScreenProcessing Screen Processing ScreenAnalysis Screen Analysis ScreenClarity User Guide, March 1, 2011 Rev Teach Screen Clarity User Guide, March 1, 2011 Rev This page intentionally left blank for duplexing purposes Main Menu Screen Setup ScreensPreferences Screen Preferences Screen Key Features of the Preferences ScreenTolerances Screen Tolerances ScreenInterface Screen Interface ScreenBlocking Screen Calibration Screen Calibration ScreenKey Features of the Advanced Screen Advanced ScreenSet Date and Time View Log Copy Logs to Flash Drive Technician ScreenStatistics Screen Statistics ScreenThis page left blank intentionally for duplexing purposes Calibration Clarity User Guide, March 1, 2011 Rev Clarity User Guide, March 1, 2011 Rev Touch Screen Calibration Screen Touch Screen CalibrationClarity User Guide, March 1, 2011 Rev This page intentionally left blank for duplexing purposes Distance Power Advanced Screen in the Setup MenuPrism Power Near PowerLens Feature Detection Warm-Up TimeSetup Password Job Data LogHome This screen intentionally left blank for duplexing purposes Maintenance Tips MaintenanceCleaning the LCD Cleaning the Touch ScreenThis page left blank intentionally for duplexing purposes Intended USE & Limitations Clarity User Guide, March 1, 2011 Rev Glossary of Terms Clarity User Guide, March 1, 2011 Rev External Connections Appendix a General SpecificationsTechnical Specifications Certifications & Standards Appendix BThis page left blank intentionally for duplexing purposes To be supplied Appendix C Electrical DiagramThis screen intentionally left blank for duplexing purposes Appendix D Certificate of Compliance
Top Page Image Contents