Siemens L-828 manual Terminal Block TB2 Label Function, Remote on-command voltage

Page 29

L-828 CCRs LC-Type (4, 7.5, and 10 kW/6.6 A/60 Hz)

Installation

Wiring Connections and

Startup (contd.)

5.Refer to Table 2-5. Install appropriate external lightning arrestors on the input power supply lines as close as possible to the CCR’s input terminal block TB3 (12).

NOTE: If optional lightning arrestors are ordered with the regulator, they are factory-installed.

NOTE: Since lightning is a phenomenon that varies in intensity and frequency with geographical locations, it is recommended that each installation evaluate the need for additional lightning protection.

6.Short-circuit the output terminals on TB1 (10) using AWG 10 (minimum) wire.

7.Refer to Table 2-4. Connect the voltage supply lines from the disconnect switch or main circuit breaker to the CCR input terminal block TB3 (11). Tighten all connections.

NOTE: Do not route the output cable in the vicinity of other wiring sensitive to EMI or RFI.

8.Energize the regulator by engaging the main circuit breaker or disconnect switch. Turn the regulator’s circuit breaker CB1 (7) to the on position, and turn rotary selector switch S1 (6) to all brightness steps. Verify current values on the panel ammeter (1) correspond to those in Table 2-8.

9.De-energize regulator by disengaging the main circuit breaker or disconnect switch. Turn the rotary switch S1 to the OFF position.

10.Connect the remote control lines, if required, to remote control terminal block TB2 (11). All CCRs use AWG 19, 300 V or larger control wire size. See Figures 3-4 and 3-5 for remote control connections.

NOTE: Tables 3-2 through 3-4 give the necessary connections for remote control. Terminal B1 (or B10) does not need to be wired. Brightness step B1 (or B10) occurs when the regulator is switched on.

Table 3-2 Remote Control Connections

Terminal Block TB2 Label

Function

N

Remote control common

CCI

Remote control power

CC

Remote on-command voltage

B10, B30, B100

Brightness control (3-step CCR)

B1, B2, B3, B4, B5

Brightness control (5-step CCR)

2002 Siemens Airfield Solutions, Incorporated

96A0104B

Page 3-7

All rights reserved

Issued 6/02

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Constant Current Regulators LC-Type 5, and 10 kW/6.6 A/60 Hz Rev Description EC No Checked Approved Date Record of ChangesTable of Contents CCRs LC-Type 4, 7.5, and 10 kW/6.6 A/60 Hz Table of Contents L-828 CCR List of Figures List of TablesWarranties Disclaimers Introduction Safety Symbols SafetySafety Symbols contd Qualified Personnel Intended Use Installation Installation contd Operation CCRs LC-Type 4, 7.5, and 10 kW/6.6 A/60 Hz Safety Introduction Description4, 7.5, and 10 kW CCRs are designed to Indicator Purpose IndicatorsCCRs LC-Type 4, 7.5, and 10 kW/6.6 A/60 Hz Description Transformers ContactorHz LC-Type L-828 CCRs 10 kW/6.6 a Required EquipmentSpecifications Input Power Breaker SizingRatings ClassClass Style Brightness Nominal Output Power Style Power Factor Efficiency Reactive LoadingResistive Loading Class Style Step Nominal Output Allowable RangeRegulation Environmental Operating Conditions Temperature RangeRelative Humidity Altitude4340 W Lb kg WeightCCR Dimensions Floor Mounting Section InstallationDescription Quantity Manufacturer Part Number Rack MountingRack Mounting contd Wiring Connections and StartupWiring Connections Startup contd Remote Control Wiring 3-Step Wiring Connections Startup contd Terminal Block TB2 Label Function Remote on-command voltageIf you use 5-Step CCR Remote Intensity If you use 3-Step CCR Remote Intensity Connect CCI to… Step…TP9 Wiring ConnectionsWiring Connections Startup contd Calibrating Regulator Adjusting Output Current Setting Up Regulator for CalibrationCCR S1 Position Ammeter Reading Potentiometer Adjusting Output Current contdAdjusting Overcurrent Adjusting Overcurrent contd Introduction Local Control If you set switch S1 Result is To the followingOperation Then Local Control ProceduresRemote Control Shutdown Procedure Maintenance Interval Maintenance Task Action Maintenance ScheduleShort-Circuit Test Open-Circuit Test Open-Circuit Test contd Troubleshooting Circuit Breaker/Fuses Description Function Preliminary TroubleshootingGeneral Troubleshooting Procedures General Troubleshooting Procedures contd VA-Indicator red Problem Possible Cause Corrective Action Regulator shutsDown from open Circuit protectionLED light lit contd Problem Possible Cause Corrective Action VA-Indicator redPart Number Description Quantity Introduction Using the Illustrated Parts ListParts Input Voltage 828 CCR 4-10 kW/6.6 a Part Ordering Code828 CCR General Assembly 4-10 kW/6.6 a Parts List LC-Type L-828 CCR Component Parts 1 828 CCR General Assembly 4-10 kW/6.6 a Parts List contdLC-Type L-828 CCR Component Parts 2 LC-Type L-828 CCR Component Parts 3 LC-Type L-828 CCR Component Parts 4of 828 CCR General Assembly 4-10 kW/6.6 aParts List contd CCR See -2. Refer below for the part numbers for the 7.5 kW See -2. Refer below for the part numbers for the 10 kW 828 CCR General KW/480 Vac Recommended Spare PartsKW/208-240 Vac Part Number Description10 kW/480 Vac 10 kW/208-240 VacSection Wiring Schematics LC-Type L-828 CCR Internal Wiring Schematic Part 1 LC-Type L-828 CCR Internal Wiring Schematic Part 2

L-828 specifications

The Siemens L-828 is a state-of-the-art aircraft communication and navigation system that is designed to enhance efficiency and safety in aviation operations. This system is equipped with a range of advanced features that cater to the evolving needs of modern air traffic management and avionics.

One of the standout characteristics of the L-828 is its versatile communication capabilities. It incorporates VHF and UHF radio systems, enabling flexible and reliable communication between pilots, air traffic controllers, and other aircraft. The system supports both voice communication and data link services, ensuring that critical information is exchanged seamlessly during flight operations.

In terms of navigation, the Siemens L-828 is equipped with cutting-edge Global Navigation Satellite System (GNSS) technology. This allows for precise positioning and navigation, essential for modern pilotage in complex airspace environments. With built-in performance monitoring, the system can also provide predictive analytics, which enhances situational awareness for pilots and ground controllers.

The architecture of the L-828 is designed for ease of integration with existing aircraft systems. Its modular design allows for straightforward upgrades and the incorporation of additional functionalities as aviation technology continues to evolve. This adaptability ensures that operators can extend the lifespan of their investment by easily implementing new features without requiring a complete system overhaul.

Another key feature of the Siemens L-828 is its robust cybersecurity measures. In an era where the threat of cyberattacks is growing, the system employs advanced encryption techniques and authentication protocols to safeguard sensitive communications and data. This emphasis on security ensures that both operational integrity and passenger safety are maintained.

Moreover, the Siemens L-828 has user-friendly interfaces that reduce pilot workload and enhance overall flight experience. With intuitive controls and clear displays, pilots can easily access critical information, thereby facilitating smoother and safer flight operations.

In conclusion, the Siemens L-828 represents a significant advancement in aviation communication and navigation technology. Its combination of versatile communication capabilities, advanced navigation systems, modular design, and heightened security protocols makes it a crucial tool for modern aircraft. As the aviation industry continues to evolve, systems like the L-828 will undoubtedly play an indispensable role in optimizing flight operations and ensuring safety in the skies.
Top Page Image Contents