Lexicon DC-1 owner manual Exclusive Zone 2 Control

Page 26

Installation and

Calibration

		Lexicon


	Exclusive Zone 2 Control	The DC-1 can also be used as an exclusive Zone 2 controller, allowing
		remote use of the system while the local room(the room in which the
		DC-1 is located) remains muted. To use the DC-1 in this manner, turn on the
		DC-1 by pressing the RECORD/ZONE 2 key on the remote. The unit will
		power up with the System Mute and Effect Bypass activated. The remote
		will default to Zone 2 IR Remote mode as described above, with Volume,
		Mute, Input Selection and L/R Balance controlling only the Record and
		Zone 2 outputs. To return to normal operation, simply press OFF, then ON.

Digital audio inputs can be selected for the Record/Zone 2 outputs under the following conditions:

•The digital input must be assigned to an input via the Setup: Input Configuration menu.

•The input must have REC/ZONE 2 set to DIGITAL. (TAPE and VCR1 are normally "BLOCKED", but can be changed in the Input Configuration menu.)

•The input must be selected for Main outputs.

20

Image 26

Contents DC-1 Acknowledgements Important Safety InstructionsCommunications Notice Vigtig information om sikkerhed Wichtige Sicherheitsanweisungen DC-1 Contents Contents, contd Introduction Introduction to the DC-1 About Dolby Digital AC-3 encoding Introduction to the DC-1 Unpacking and Inspection Using the Documentation Glossary of Terms DC-1 Block Diagram Display Controls IndicatorsFront Panel ZONE2 and Record Power On/OffRear Panel Mute Remote ControlOFF and on MenuRemote Control Accy Functions Signment ClearedConnection Location Considerations AC ConnectionsAudio/Video Connections Wiring ConsiderationsWire Lengths Length AWG SizeConnecting DC-1 as a preamp Installation Calibration AC-3 Ready Laser Disc LD/DVD PlayersRECORD/ZONE 2 Operation Zone 2 IR Remote Mode Enabled Zone 2 Remote ControlExclusive Zone 2 Control System Configuration Video On-Screen Display Video Input Selection On-Screen DisplaySystem Setup Input GainInput Name Restore Input Name Effect Non AC-3 Effect BaseDolby Digital Digital Audio Input Assignment Center Setting the Speaker ConfigurationFront L/R Subwoofer Output Setting Output Levels Dolby Digital version Subwoofer Peak LimiterMute Level Power On Volume Zone 2 Volume Setting Listener Position Time Alignment Dolby Digital versionCenter Delay Base and THX versionsCalibrate Panorama Installation Calibration Settings are Locked Equalization THX and Dolby Digital versions Bass and Treble LevelTilt Dolby Digital version DC-1 Effects Customizing EffectsDC-1 Effects Music Surround THX and Dolby Digital versions Music Surround ParametersPro Logic Parameters Parameter Initial Value RangeTHX Cinema THX and Dolby Digital versions THX Cinema ParametersLogic 7 THX and Dolby Digital versions Logic 7 ParametersDC-1Effects TV Matrix TV Matrix ParametersDC-1Effects Mono Logic Parameters Panorama Panorama ParametersDC-1 Effects Nightclub Nightclub ParametersConcert Hall Concert Hall ParametersChurch Church ParametersCathedral Cathedral ParametersMusic Logic Music Logic ParametersDC-1 Effects Two Channel Parameters PartyTwo Channel Party ParametersAC-3 Status Display Dolby Digital version Music Dolby Digital Music ParametersDolby Digital Dolby Digital version Dolby Digital ParametersTHX Dolby Digital version THX 5.1 ParametersLogic 7 Dolby Digital version DC-1Effects 1Two Channel Dolby Digital version Troubleshooting ProblemTroubleshooting Problem Possible Cause and SolutionTroubleshooting Routine Maintenance Restoring DefaultsSpecifications Display Time Speaker Configuration circle selectionOSD Position Listener Position PanoramaLexicon, Inc Oak Park