Panasonic AW-RP120G operating instructions Link settings, Connection destination IP addresses

Page 29

Settings for connecting with the remote cameras and switcher

To control remote cameras from the unit and use the function to link the unit and a switcher, you need to set the connection settings in advance. There are two ways of configuring the connection settings. You can either configure the settings on the unit or use the setup software to configure the settings.

This section describes how to configure the settings on the unit.

For details on how to use the setup software to configure the settings, refer to “Setup Software” in Operations and Settings (page 45).

Notes

zzAll the remote cameras are set to the same IP address when they are shipped from the factory. Therefore, if multiple remote cameras left set to the factory default state are connected with IP connections and then operated from the unit, they will not operate properly.

zzWhen another remote camera that is set to the same IP address

as an existing remote camera is to be connected because, for example, the existing remote camera is being replaced, turn off the unit’s power before making the connection. When the remote camera is connected without first turning off the unit’s power, the remote camera may not operate properly.

Link settings

Selecting one of the camera numbers CAM1 to CAM100 on the unit identifies the remote camera to control. When the remote camera you are attempting to control is connected via an IP connection, you need to set an IP address that is not a duplicate of that of each of the remote cameras and associate each IP address and each camera number on the unit beforehand in order to perform control.

Likewise, to use the function for linking with a switcher, you you need to associate the IP address of the switcher with the unit.

These association settings are referred to as “link settings” in this manual.

Connection destination IP addresses

The IP address for the unit to identify the connection target (remote camera or switcher) is referred to as the “connection destination IP address” in this manual.

One remote camera connection destination IP address for each of the CAM1 to CAM100 camera numbers (total of 100) is set on the unit, and one switcher connection destination IP address is set on the unit.

You can confirm the connection destination IP address for each camera number in MANUAL IP menu [39]. You can confirm the connection destination IP address for the switcher in SW SETUP menu [41].

Overview of related menus and operations

CTRL TYPE menu [36]

Set the connection type (serial/IP/no connection) for the remote camera to be connected for each camera number.

AUTO IP menu [37]

Use this menu when you want to configure the settings for linking with the remote cameras and a switcher automatically. (Auto IP setting) There are the following three operation modes.

RENEW IP ADR

Configures the link settings by the unit

 

renewing the IP addresses set on the remote

 

cameras and switcher.

KEEP IP ADR

Configures the link settings by keeping the

 

IP addresses set on the remote cameras

 

and switcher and renewing the connection

 

destination IP addresses set on the unit.

ALL CLEAR

Initializes the connection destination IP

 

addresses set on the unit.

SWAP IP menu [38]

Use this menu when you want to change the camera number and connection destination IP address combinations linked by auto IP setting.

MANUAL IP menu [39]

Use this menu when you want to check or manually change the connection destination IP address set for each camera number.

SW SETUP menu [41]

Use this menu when you want to set the connection type (IP/no connection) for the switcher to be linked with the unit or set the connection destination IP addresses.

29

Image 29
Contents Operating Instructions Pp Come aprire i file dei manuali di istruzioni per l’uso It can be downloaded from the home page of Adobe SystemsFCC Note Read this firstImportant Safety Instructions Performance level EMC Notice for the PURCHASER/USER of the ApparatusContents Restrictions on use User authenticationIntroduction Supported remote cameras FeaturesSupported switcher Precautions for use AccessoriesExample of embedding the unit in a desktop Precautions for installationMake mount angles suitable for the installation location Unit mm inch AppearanceZzMount angle attachment position Menu operation section Parts and their functionsControl panel Pan and tilt section Camera selection sectionFocus, zoom and iris section Color adjustment section Menu and memory selection section Indicator section ZzMemory cards User button sectionMemory card section Rear panel About the external DC power supplyBasic operations of the unit Shutter Basic operations for the menusOff SpeedExamples of IP connections ConnectionsConnections „„Serial connections for AW‑HE120 remote cameras Examples of serial connections„„Serial connection for a remote camera AW‑HE50 or AW‑HE60 Supported camera ZzSwitch settings of AW-IF400ZzUse a straight cable category 5 or above for the LAN cable „„Serial connections for AW-PH650 and cameraSetting the subnet mask Network settings of the unitSetting the IP address of the unit Setting the default gatewaySetting Global Area Setting the reception port numberPort CAM1 Displaying the MAC addressOverview of related menus and operations Link settingsConnection destination IP addresses When configuring the settings for the first time Setting the IP addresses automatically auto IP settingCAM1 NoAsign SW CTLAuto SET Auto SET SET UP ERRAuto SET Complete Auto SET Renew IP ADRCAM2 Network CAM3 Network CAM4 NoAsign C001/004 S0/1Remote camera D 192.168.000.200 Turn the F2 dial to select Yes, and then press the F2 dialConnection destination IP address of CAM4 Retry Auto SET Keep IP ADROVER! YES CAM1 192.168.000.003 Swapping connection destination IP addressesCAM1 IP Duplicate Press the F2 dial to confirm the IP addressCAM1 Setting the connection destination port numberSW IP Address 192.168.000.008Selecting a camera group Selecting a camera groupSelecting a remote camera Troubleshooting „„General Specifications„„Input/output connectors Index Memo Memo For business users in the European Union

AW-RP120G specifications

The Panasonic AW-RP120G is a sophisticated remote camera controller designed for broadcasting and production environments that require precise control over multiple pan-tilt-zoom (PTZ) cameras. This versatile controller offers an extensive range of features, making it a reliable choice for professionals in the field.

One of the key highlights of the AW-RP120G is its user-friendly interface. It incorporates a large, LCD touchscreen display that provides real-time information and control options for both novice and experienced operators. The layout is intuitive, enabling quick access to various settings without the need for complex configurations. This allows operators to focus on their production rather than getting mired in technical details.

The AW-RP120G is equipped with the capability to control up to 200 PTZ cameras simultaneously, which caters to large-scale productions. This flexibility is crucial in various settings, from live events to studio broadcasts, where multiple camera angles and shots are necessary. The controller utilizes IP connectivity and supports the Panasonic’s proprietary protocol, ensuring seamless operation across a networked environment.

Another standout characteristic of the AW-RP120G is its advanced preset management system. Users can store and recall up to 100 preset camera positions, eliminating the need to manually adjust each PTZ camera during a live performance. This feature significantly enhances workflow efficiency and allows for smooth transitions between camera angles.

The device further incorporates advanced technologies, such as PoE (Power over Ethernet) compatibility, which simplifies installation by allowing power and data to be transmitted over a single cable. This reduces clutter and streamlines setup processes, particularly in complex environments.

In terms of design, the AW-RP120G is compact and portable, making it easy to integrate into various production setups. It is built with durability in mind, ensuring that it can withstand the rigors of frequent use in demanding environments.

Overall, the Panasonic AW-RP120G is a state-of-the-art remote controller that combines functionality, efficiency, and reliability. With its advanced features, it is an essential tool for any professional looking to elevate their camera operation capabilities in broadcasting and live event production. This makes it a valuable investment for those looking to enhance their production quality while streamlining their workflow.