Maha Energy IW7 WB / WBV, IW4 WB / WBV manual Preparations for a Brake Test, Running a Brake Test

Page 26

Operations

IW4/IW7 WB/WBV

3.4Preparations for a Brake Test

The procedures described here are for normal operation of 4 wheel drive test stands. (4 wheel drive switch to position "0"). There is a seperate description available for the 4 wheel drive test. (See Tele-BPS II + RCF 30 operating manual).

If the test stand is equipped with an internal scale no weight may burden the roller set when the test stand is switched on. Otherwise the weighing electronic will store this switch on weight as an Offset value and the measurement will be distorted.

!Enable main switch

The needle of the display will complete an offset balance and return to zero.

!Press POWER ON key

Press POWER ON button or the '*' key on the remote control.

The white POWER ON lamp should now be lit up. The needles will again adjust and return to zero. The test stand is now ready for operation!!

On test stands without a PC-console but equipped with a DIN A4-printer which is offline or defective, the message "Printer defective (ONLINE?)" will appear after switch-on. If the test should be carried out without the printer, the printer can be de-activated by pressing the Power On button again.

!Select the measuring range (optional)

If the test stand is equipped with a manual measurement range button, use it to select the desired measurement range. The integrated green lamp will light up when the large measurement range is selected.

!Conduct a single-wheel test (optional)

Test stand which are not equipped with a remote control have a single wheel switch which facilitates single wheel testing. Depending on the test stand version the Power-On key must be pressed after a single wheel test.

The rollers will start up automatically after a single wheel test when the switch has been re-set to the 0 position.

3.5Running a Brake Test

The manufacturer does not accept any liability claims for damage to low lying vehicle parts.

Drive first axle to be tested onto the roller set switch into idle. After the delayed start-up, the motors will be started individually. Should the motors switch off again immediately, the start-up monitor has been triggered to protect your vehicle and/or its tires against damage. One or both wheels may be jammed (seized bearings, jammed brake pads, etc.).

22

D1 0412BA1-GB04

Page 25 Page 27
Image 26
Page 25 Page 27
Contents IW4 WB / WBV IW7 WB / WBV IW4/IW7 WB/WBV Description SafetyMaintenance, Error Codes OperationsIW4/IW7 WB/WBV General Information about Brake Testing IntroductionPrinciple of 4 Wheel Drive Vehicle with a Driven Axle2 4-Wheel Drive Vehicle Testing of various 4-wheel drive types Disengageable drive shaft leading to the differentialRigid drive shaft between the differentials Electrical Data Technical DataMain switch fuse Main switch fuse with special voltage Wheel driveRoller friction coefficients Mechanical DataTest speed Display range depending on modelElectronic Standard Equipment IW4/IW7 WB/WBV 4WDNoise Emission OptionalEquipment IW7 MB Version Safety Safety Regulations for Service Work Safety Regulations for CommissioningSafety Regulations during Operation Exchange of Parts Combination with AccessoriesFurther Information Pit Safety Option Safety FeaturesLockable Main Switch Sensor Rollers Brake TesterReady Symbol DescriptionPower on Automatic/MalfunctionRoller Heating Remote ControlPit Safety Device GraphicSlip Switch-Off Control MB-Mode Symbol Description Driving Direction ReverseSpeed Switch-Over Unoccupied-Simulation for Weight SimulatorIW7 4 wd Standard equipment iwth optional accessories IW7 Equipment VariationsIW4/IW7 WB/WBV IW7 4 wd Mercedes Benz-version IW4 Equipment Variations IW4 expansion stepIW4 expansion level IW4/IW7 WB/WBV Preparations for a Brake Test Running a Brake TestApply moderate force to the brake pedal Determining the Roller ResistanceOvality Test optional Ovality MeasurementMaximum Brake Force Test Brake TestSpecial Features on Test Stands with MB Mode Imbalance Display OptionalSpecial Points about the Portugal-Mode Special Points about the Sweden ModeSelect weight transfer Drive onto the test standSlip is too small Special Points about the Hongkong ModeTest Procedure IW4/IW7 WB/WBV Maintenance, Error Codes Maintenance of the Roller SetDescription of Error Codes General Error CodesNotify the customer service dept Selector switch Driving DirectionSwitch Driving Direction Reverse to position Immediately when sensor roller defects occurInstallation and Dismantling of the Test Stand Additional Defect Codes on 4-Wheel Drive Test StandsPage Page Qualitätsnachweis Produkte Installation, Inbetriebnahme & Nachfolgeservice

IW4 WB / WBV, IW7 WB / WBV specifications

Maha Energy has been at the forefront of innovative technologies in the oil and gas sector, particularly with the introduction of its IW7 WB / WBV and IW4 WB / WBV systems. These advanced technologies are designed to optimize production, increase efficiency, and enhance overall resource management in hydrocarbon extraction.

The IW7 WB and WBV systems are known for their robust design and efficient performance. These systems integrate state-of-the-art technology with user-friendly interfaces, enabling operators to monitor and control production from a centralized location. The IW7 series boasts a modular architecture, allowing for easy upgrades and maintenance, providing a future-proof solution for energy production.

One of the standout features of the IW7 WB / WBV is its advanced wellbore stability technology. This feature significantly reduces the risk of wellbore collapse and enhances the longevity of the production wells. Additionally, the system incorporates real-time data analytics, enabling operators to make informed decisions on production optimization and resource allocation. The use of predictive maintenance schedules further minimizes downtime, ensuring that production remains consistent and efficient.

Similar in innovation, the IW4 WB and WBV systems offer exceptional versatility and reliability. These models cater specifically to varying production environments and can be tailored to meet specific operational needs. The IW4 series is equipped with advanced sensors and automation capabilities, allowing for seamless integration with existing infrastructure and enhanced data collection for performance analysis.

Both IW7 and IW4 systems utilize cutting-edge materials designed to withstand harsh operational conditions, ensuring durability and reducing maintenance costs. The systems use intelligent controls to optimize flow rates and minimize energy consumption, demonstrating Maha Energy's commitment to sustainable practices in the industry.

Furthermore, the environmental impact of these technologies has been carefully considered. By improving efficiency and reducing waste, the IW7 and IW4 systems contribute to lower emissions and a lesser environmental footprint.

In conclusion, Maha Energy's IW7 WB / WBV and IW4 WB / WBV technologies represent a significant leap in oil and gas extraction systems. Through their advanced features, robust design, and commitment to sustainability, these systems are set to redefine standards in the industry, ensuring that energy production is both efficient and eco-friendly. As the energy landscape continues to evolve, Maha Energy remains dedicated to providing innovative solutions that meet the demands of tomorrow’s energy market.
Top Page Image Contents