Sharp CV-2P10SC operation manual Before Calling for Service

Page 30

BEFORE CALLING FOR SERVICE

If the unit appears to be malfunctioning, check the following points before calling for a ser- vice.

UNIT DOES NOT OPERATE AT ALL

•Is the unit plugged in or is the plug loose?

•Has the fuse blown or is the circuit breaker tripped?

•Did you restart the unit within 3 minutes of a power failure?

If the power was off for less than 3 minutes when, you restarted the unit, a protective de- vice may cause the compressor to shut off, preventing cooling for about 5 minutes.

•Are the AIR CON, TIMER and MAXIMUM lamps blinking?

The water tank inside the unit is full. It must be drained. (See page 26)

•Check the power plug. (See page 16)

UNIT DOES NOT COOL PROPERLY

•Is it set to FAN, DEHUMIDIFICATION, VENTILATION, ION GENERATOR mode? Cooling does not take place in these modes. Change the MODE setting.

•Is the filter clogged with dust? Clean the filter.

•Is the cooling coil frozen?

No air will blow out if the cooling coil is frozen.

Run the unit in FAN mode with the fan speed set to "HIGH" until all ice dissipates.

•Is the temperature set properly?

•Is the window exposed to direct sunlight?

Close the curtains or blinds to minimize solar energy heating the room.

•Is the exhaust hose too long?

For efficient operation, make the hose as short as possible. The exhaust hose must not be twisted or bent.

SOUNDS

•The unit may seem rather loud for the first 2 to 3 minutes when the unit is turned on.

This is the sound of the compressor starting-up and is perfectly normal.

•A soft, swishing noise can be heard immediately after the unit is turned on or off, and also during operation. This is the sound of the refrigerant flowing inside the unit.

•A low buzzing noise is emitted when the unit is generating Plasmacluster ions.

•This unit evaporates water condensed during cooling operation within the unit through the exhaust air outlet. Although water flowing sound way be heard, this is normal.

•An audible gurgling sound may be heard when the unit is operated on a gently sloping floor. Place the unit on a level floor.

TIMER DOES NOT WORK PROPERLY

•If a power failure occurs while the TIMER is set, the TIMER setting will be cancelled and will not be retrieved even after the power is restored. This is normal for this unit.

THE UNIT FAILS TO REACT TO THE REMOTE CONTROL SIGNAL

•Check the batteries in the remote control. Replace if necessary.

•Try to send the signal again with the remote control pointed directly at the unit’s signal receiver window.

•Check whether the remote control batteries are installed with the polarities properly aligned.

THE DISCHARGED AIR HAS AN ODOR

•Plasmacluster ion generator emits small traces of ozone which may produce an odor. These ozone emissions are below safety levels and comply with the federal ozone emissions limit.

EN-28

CV-2P10SC_en.indd 28

11.3.22 11:00:19 AM

Page 29 Page 31
Image 30
Page 29 Page 31
Contents CV-2P10SC Page Contents EnglishFor Customer Assistance the United States Consumer Limited Warranty Consumer Limited Warranty for the U.S. UsersPrecautions Radio or TV InterferenceUsage Cautions Drainage should be performed whenever moving the unitOperating Conditions Energy Efficiency TipsSuggested Tools for Window Panel Installation LocationIncluded Part Names Front View Rear ViewION Mode only Remote ControlAIR CON Mode only Remote Control DisplayAttach the guard combined above to Install Window PanelGuard net Window panelUse the window panel and the adjustment panel Attach the guard combined above to the window panel Inner height of the window 28.3 718mm 45.3 1150mm Installation and Removal of Exhaust Hose Removal of the exhaust hose Remove the window adapter Remove the exhaust hose from the unitRemove the battery cover Insert two batteries. AAAR03 Power Plug CheckPress the Reset button until you hear another Click PRE-OPERATION ChecksHOW to USE the Remote Control USE for AIR Conditioner Cool ModeDehumidification Mode To Turn OFFPress the Mode button to select FAN mode FAN ModeVentilation Mode Press the FAN button to set fan speedPress the Louvers button again to stop the desired position To Change AIR Flow DirectionUP / Down AIR Flow Direction Left / Right AIR Flow DirectionTo Cancel MAX Cool OperationSleep Operation Timer Operation On TimerOFF Timer ION Generator Mode USE for ION GeneratorPress the ION button to start operation MAX Density Operation Press the MAX Density button during Ion generator operationPress the MAX Density button again Press the Refresh button during Ion generator operation OFF Timer OperationRefresh Operation Press the Refresh button againMain Unit Operation Press the Power button to start opera TionPress the Power button during opera Tion DrainageCleaning the Unit and the Remote Control MaintenanceCleaning the Filter Before NON-USE for a Long PeriodBefore Calling for Service Acondicionador DE Aire Para Habitacion CV-2P10SC ÍndiceDeclaración de Conformidad Parte ResponsableSolicitu DE Servicio AL Cliente Estados Unidos Garantía Limitadaal Consumidor Garantía Limitada DEL Consumidor Para Usuarios DE EE.UUAdvertencia Para EL Cable Desuministro DE Energia PrecaucionesAdvertencias Para EL USO Interferecias de Radio o TVAdvertencia Acerca DE LA CO- Nexión a Tierra Precauciones Para EL USOObservaciones Sobre EL Funcionamiento Condiciones DE FuncionamientoConsejos Para EL Rendimiento DE Energía Ubicación Piezas IncluidasNombre DE LAS Piezas Parte Delantera Parte TraseraSolamente Modo ION Control RemotoSolamente Modo AIR CON ComúnInstalación DEL Panel DE Ventana Instalación en una ventana de guillotina dobleFije el soporte con un tornillo. Recomendado ES-12 ES-13 Instalación Y Desmontaje DE LA Manguera DE Escape Fije el adaptador de la manguera de escape a la unidadES-15 Inspecciones Antes DEL USO Presione el botón de reinicio ResetPresione el botón Reset hasta que es- cuche otro Clic Colocacion DE LAS PilasForma DE Usar EL Control Remoto Modo Deshumidificación USO Para EL Acondicionador DE AireModo Enfriar DesactivaciónModo Ventilador Modo VentilaciónPresione el botón Louvers Cambio DE LA Dirección DE Flujo DE AireDirección DEL Flujo DE Aire Hacia ARRI- BA/ABAJO Flujo DE LA Corriente DE Aire Hacia LA IZQUIERDA/DERECHACancelar Operacion Enfriamiento MaximoOperacion DE Dormir Funcionamiento CON EL Temporizador Activación DEL TemporizadorDesactivación DEL Temporizador USO Para Generador DE ION Modo ION GeneratorPresione el botón ION para iniciar el funcio- namiento Dirección DE Flujo DE Aire Hacia ARRI- BA/ABAJO USO Para ION GeneratorOperacion Maxima Densidad Presione nuevamente el botón MAX DensityOperacion Refrescar Operacion Desactivación DEL TemporizadorPresione nuevamente el botón Refresh Funcionamiento DE LA Unidad Principal Presione el botón Power para iniciar el FuncionamientoPresione el botón Power durante la operacion DrenajeLimpieza DE LA Unidad Y DEL Control Remoto MantenimientoLimpiando EL Filtro Antes DE UN no USO POR UN Largo PeriodoAntes DE Llamar AL Departamento DE Servicio Técnico Page Sharp Plaza, Mahwah New Jersey 07495-1163 U.S.A

CV-2P10SC specifications

The Sharp CV-2P10SC is a state-of-the-art portable air conditioner designed to deliver efficient cooling performance while prioritizing user comfort and convenience. With a sleek and modern design, this air conditioning unit is not only functional but also enhances the aesthetic appeal of any space it occupies.

One of the standout features of the Sharp CV-2P10SC is its powerful cooling capacity of 10,000 BTU, making it suitable for medium-sized rooms up to 25 square meters. This unit effectively lowers indoor temperatures, providing a refreshing environment during hot summer months. Additionally, it boasts a dehumidification function, which helps remove excess moisture from the air, creating a more comfortable atmosphere.

Equipped with a user-friendly control panel and remote control, the Sharp CV-2P10SC ensures that adjusting temperature settings and other functions is simple and convenient. The intuitive controls allow users to select from multiple fan speeds, temperature settings, and operational modes, including cooling, fan, and dehumidification modes. The programmable timer feature further adds to its versatility, allowing users to set the unit to turn on or off at desired times.

The Sharp CV-2P10SC incorporates advanced technologies for energy efficiency. It is designed with an eco-friendly R32 refrigerant, which has a lower global warming potential compared to traditional refrigerants. This not only supports environmental sustainability but also contributes to reduced energy consumption, ultimately leading to lower electricity bills.

Another significant characteristic of the CV-2P10SC is its portability. The unit comes with integrated wheels, making it easy to relocate from one room to another as needed. This flexibility means users can enjoy cool air in any area of their home, whether it’s the living room, bedroom, or office.

Noise levels are kept to a minimum, thanks to its efficient design and technology, ensuring that the unit operates quietly while delivering powerful cooling performance. This is particularly beneficial for nighttime use or in settings where noise could be disruptive.

Overall, the Sharp CV-2P10SC combines robust cooling capabilities, advanced technology, and user-friendly features to provide an exceptional indoor climate control solution that meets the needs of modern consumers. Whether for daily use or special occasions, it stands out as an excellent choice for anyone seeking reliable and efficient portable cooling.
Top Page Image Contents