Sharp MD-M3H operation manual Minidisc Operation, MD playback, To remove a MiniDisc

Page 14

MINIDISC OPERATION

■MD playback

1 Press the ON/STAND-BY button to turn the power on.

2 Press the MD button.

3 Load a MiniDisc in the direction indicated by the arrow on the MiniDisc, with the labeled side fac- ing up.

1

3

7

●The total number of tracks and the total playing time on the MiniDisc will be displayed.

4 Press the 0 6 button.

● If the MD has a track name, the name will ap-

pear and scroll across the display. Then, the

H 4

elapsed playing time will appear.

● If the MD has no track names, the elapsed play-

2

2

H

ing time will appear.

● When the last track has been played back, the

unit will stop automatically.

To interrupt playback:

Press the 0 6 button.

● " 6 " will appear.

● Press the 0 6 button again to resume playback

1

4

from the same point.

To stop playback:

Press the ■ button.

To remove a MiniDisc:

Press the 7 MD EJECT button.

DISC
MEMORY
RANDOM	kHz REC
TOTAL	kHz REC
REMAIN	MHz SLEEP

Disc name

(Displayed only when a disc name has been programmed)

Flash

DISC TOC
TRACK
MEMORY
RANDOM	kHz REC
TOTAL	kHz REC
REMAIN	MHz SLEEP

Total number of tracks Total playing time

Notes:

●If TV or radio interference occurs when using the MD, move the unit away from the TV or radio.

●Although MiniDiscs will not normally skip due to vibration, you may hear a skip in the sound if there is continuous vibration.

If the volume is turned up too high, a skip may occur depending on the contents of the MD.

If this happens, turn the volume down and the skipping should stop.

●If any (or some) error messages is displayed dur- ing MD operation, see "ERROR MESSAGES" on page 47.

12

Image 14

Contents Contents MD-M3HTerms of Guarantee A9903.YTService Information Special NotesVolume control AccessoriesPrecautions GeneralRear panel Names of Controls and IndicatorsFront panel Speaker section 16 17 18 19 20 21Display window Remote control MD/CD SectionSpeaker connection Preparation for USEAerial connection Speaker cushion Removing the speaker grilles Connecting the AC power leadDemo mode Placing the systemPlay Remote controlPrecautions for battery use To change the brightness of the disTo see the time display Setting the ClockTo change the time display mode To change the clock timeExtra bass X-BASS VolumeSound Control Pre-programmed equalizer SurroundTo interrupt playback Compact Disc OperationCD playback To stop playbackTo remove a MiniDisc Minidisc OperationMD playback Repeat and random play Convenient CD and MD OperationApss Auto Program Search Sys- tem Cue and reviewTo clear the programmed selections To cancel the ApmsApms Automatic Programmable Music Selector To check which tracks are programmedTime Switching the time displayChanging the display during MD playback Auto tuning TuningManual tuning Press the ON/STAND-BY button to enter the stand- by modePreset tuning Preset memory scanPTY Display ModeInformation provided by RDS Test Alarm None To stop the Aspm operation before it is complete To erase all of the contents of preset memoryAspm Auto Station Program Memory To cancel the station select operation Page If you have selected the traffic programme To manually recall the stations stored in memory To switch the displayPresetx W About the Ptyi Dynamic PTY Indicator Checking the stand-by mode settingTo cancel the EON stand-by mode MeaningWhen in the EON stand-by mode, press the EON button EON-TIAbout the TP and TA indicators TP indicator TA indicator MeaningDisc writing TOC About track numbers RecordingDifferences from tape recordings To check the remaining time available for recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingCD0MD Edit High /NORMAL To record without using One-Touch EditingApms recording Recording is performed as a single track Recording from the built-in radio onto a MiniDiscTo record the track number whilst record- ing Type of characters used EditingWhat the editing function can do Within 10 seconds, press the Enter button To create a disc nameTo erase a disc name Press the Enter button to enter the characterTo create a track name To erase a track nameName TOC Edit Enter Clear To change disc names and track namesTo add a character Example To change Besut to BestCombine When both tracks have a nameDivide Example MoveTo combine two non-contiguous tracks To erase tracks one at a time EraseAll Erase To erase all of the tracks at onceTimer Operation Timer playbackTimer recording To use sleep and timer playback in combi- nation Simultaneous sleep and timer op- erationTo cancel the sleep operation To use sleep and timer recording in com- binationHeadphones Using External UnitsConnecting external units Listening to sound from an exter- nal unit Manual recordingWhat is a MINIDISC? Symptom Possible cause Remedy TroubleshootingIf a problem occurs Mini Disc System LimitationsMD recording and playback Symptom Possible causeCD Playback Radio receptionError Messages When an error message is displayed, proceed as followsCare of compact discs Resetting the Microcom Maintenance PuterExternal care Specifications Memo