Sharp MD-M3H operation manual Sleep operation, Simultaneous sleep and timer op- eration

Page 43

(Continued)

Caution:

In the following cases, the timer recording function will not work.

●When a MiniDisc has not been inserted.

●When a playback-only MiniDisc is inserted.

●When the MiniDisc you inserted is protected against accidental erasure.

●When there is no recording space left on the Mini- Disc you have inserted (when the “TOC FULL *” or “DISC FULL” messages appear).

■Sleep operation

The radio, compact disc and MiniDisc can all be turned off automatically.

(Remote control operation)

To cancel the sleep operation:

Press the ON/STAND-BY button to enter the stand- by mode.

The sleep operation can also be cancelled as fol- lows if you can not set the unit to the stand-by mode during recording.

1Press the SLEEP button.

●“SLEEP” will flash.

2Within 5 seconds, press the SLEEP button again.

●The sleep operation will be cancelled. (“SLEEP” will go off.)

Notes:

● Once the sleep time is set, it will remain the same

duration until the setting is changed.

● The sleep functions of this unit cannot be used

to control equipment connected to this unit. You

must use the sleep functions of the other equip-

TIMER

/

ment, if it has them.

SLEEP
ENTER	5 3 /
	5 3 /
	2 4

1 Play the desired sound source.

2 Press the SLEEP button.

SLEEP

SLEEP

●If you do not need to change the time, the unit will enter the sleep mode automatically.

3 Within 5 seconds, press the ENTER button.

SLEEP

4 Press the or button to adjust the time.

(Maximum: 2 hours - Minimum: 1 minute)

The amount of sleep time can also be changed during the sleep operation.

SLEEP

5 Press the ENTER button.

DISC TOC
TRACK
MEMORY
RANDOM	REC	SLEEP
TOTAL	REC
REMAIN	SLEEP

6 The unit will enter the stand-by mode automati- cally after the preset sleep time has elapsed.

■Simultaneous sleep and timer op- eration

To use sleep and timer playback in combi- nation:

1Perform steps 1 - 9 on page 39 “Timer playback”.

2Perform steps 1 - 5 of the “Sleep operation” on this page.

To use sleep and timer recording in com- bination:

1Perform steps 1 - 9 on page 40 “Timer record- ing”.

2Perform steps 1 - 5 of the “Sleep operation” on this page.

Sleep timer setting
Timer playback	Timer playback
(record) setting	(record) start
1 minute - 2 hours		Desired time
Sleep operation will		End time
automatically stop.

41

Image 43

Contents MD-M3H ContentsA9903.YT Terms of GuaranteeSpecial Notes Service InformationGeneral AccessoriesPrecautions Volume controlFront panel Names of Controls and IndicatorsRear panel Display window 16 17 18 19 20 21Speaker section MD/CD Section Remote controlAerial connection Preparation for USESpeaker connection Placing the system Removing the speaker grilles Connecting the AC power leadDemo mode Speaker cushionTo change the brightness of the dis Remote controlPrecautions for battery use PlayTo change the clock time Setting the ClockTo change the time display mode To see the time displayPre-programmed equalizer Surround VolumeSound Control Extra bass X-BASSTo stop playback Compact Disc OperationCD playback To interrupt playbackMD playback Minidisc OperationTo remove a MiniDisc Cue and review Convenient CD and MD OperationApss Auto Program Search Sys- tem Repeat and random playTo check which tracks are programmed To cancel the ApmsApms Automatic Programmable Music Selector To clear the programmed selectionsChanging the display during MD playback Switching the time displayTime Press the ON/STAND-BY button to enter the stand- by mode TuningManual tuning Auto tuningPreset memory scan Preset tuningInformation provided by RDS Display ModePTY Test Alarm None Aspm Auto Station Program Memory To erase all of the contents of preset memoryTo stop the Aspm operation before it is complete To cancel the station select operation Page If you have selected the traffic programme Presetx W To switch the displayTo manually recall the stations stored in memory Meaning Checking the stand-by mode settingTo cancel the EON stand-by mode About the Ptyi Dynamic PTY IndicatorEON-TI When in the EON stand-by mode, press the EON buttonTP indicator TA indicator Meaning About the TP and TA indicatorsDifferences from tape recordings RecordingDisc writing TOC About track numbers To stop recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To check the remaining time available for recordingApms recording To record without using One-Touch EditingCD0MD Edit High /NORMAL To record the track number whilst record- ing Recording from the built-in radio onto a MiniDiscRecording is performed as a single track What the editing function can do EditingType of characters used Press the Enter button to enter the character To create a disc nameTo erase a disc name Within 10 seconds, press the Enter buttonTo erase a track name To create a track nameExample To change Besut to Best To change disc names and track namesTo add a character Name TOC Edit Enter ClearDivide When both tracks have a nameCombine To combine two non-contiguous tracks MoveExample To erase all of the tracks at once EraseAll Erase To erase tracks one at a timeTimer playback Timer OperationTimer recording To use sleep and timer recording in com- bination Simultaneous sleep and timer op- erationTo cancel the sleep operation To use sleep and timer playback in combi- nationConnecting external units Using External UnitsHeadphones Manual recording Listening to sound from an exter- nal unitWhat is a MINIDISC? Mini Disc System Limitations TroubleshootingIf a problem occurs Symptom Possible cause RemedyRadio reception Symptom Possible causeCD Playback MD recording and playbackWhen an error message is displayed, proceed as follows Error MessagesExternal care Resetting the Microcom Maintenance PuterCare of compact discs Specifications Memo