Sharp MD-M3H operation manual Timer recording

Page 42

(Continued)

●Before setting the timer, make sure that the clock setting is correct. (Page 9)

■Timer recording

Before timer recording, the following preparations are required.

●Load a CD, a recordable MD.

●Preset the radio station.

(Remote control operation)

3

4,5,6,7,8

5,6,7,8

	2
1,10	9

1 Press the ON/STAND-BY button to turn the power on.

2 Press the CD, TUNER(BAND), AUX button to select desired function.

3 Press the TIMER button to select the timer recording mode.

4 During “f REC” is flashing, press the ENTER button.

REC	REC

DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

5 Within 5 seconds, press the or button to set the hour to start, and then press the ENTER button.

REC

REC

6 Press the or button to set the minute to start, and then press the ENTER button.

REC

REC

●If not set manually, the ending time will automati- cally be set for one hour after the starting time.

7 Press the or button to set the hour to stop, then press the ENTER button.

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

8 Press the or button to set the minute to stop, then press the ENTER button.

	REC
DISC TOC
TRACK
MEMORY
RANDOM	REC
TOTAL	REC
REMAIN	SLEEP

REC REC

9 Rotate the VOLUME control to adjust the sound volume.

●Be careful not to turn the volume up too high.

10 Press the ON/STAND-BY button to enter the stand-by mode.

●The timer set indicator will light up.

11 When the timer start time is reached, timer recording will start.

12 When the timer end time is reached, timer recording will stop.

●“f REC” will disappear, and the timer mode will be cancelled.

The unit will enter the stand-by mode.

Notes:

●The timer cannot control the component con- nected to the Auxiliary Input sockets.

●When the available recording time has been con- sumed, the recording will stop.

To change the programmed contents:

Start again from step 1.

To confirm the timer setting:

Press the TIMER button once.

●The turn-on time, the turn-off time and name of sound source will be displayed.

To cancel timer operation:

1Whilst in the timer stand-by mode, press the ON/ STAND-BY button to turn the power on.

2Press the ON/STAND-BY button repeatedly to turn off the timer, “f REC” will go out.

40

Image 42

Contents Contents MD-M3HTerms of Guarantee A9903.YTService Information Special NotesVolume control AccessoriesPrecautions GeneralNames of Controls and Indicators Front panelRear panel 16 17 18 19 20 21 Display windowSpeaker section Remote control MD/CD SectionPreparation for USE Aerial connectionSpeaker connection Speaker cushion Removing the speaker grilles Connecting the AC power leadDemo mode Placing the systemPlay Remote controlPrecautions for battery use To change the brightness of the disTo see the time display Setting the ClockTo change the time display mode To change the clock timeExtra bass X-BASS VolumeSound Control Pre-programmed equalizer SurroundTo interrupt playback Compact Disc OperationCD playback To stop playbackMinidisc Operation MD playbackTo remove a MiniDisc Repeat and random play Convenient CD and MD OperationApss Auto Program Search Sys- tem Cue and reviewTo clear the programmed selections To cancel the ApmsApms Automatic Programmable Music Selector To check which tracks are programmedSwitching the time display Changing the display during MD playbackTime Auto tuning TuningManual tuning Press the ON/STAND-BY button to enter the stand- by modePreset tuning Preset memory scanDisplay Mode Information provided by RDSPTY Test Alarm None To erase all of the contents of preset memory Aspm Auto Station Program MemoryTo stop the Aspm operation before it is complete To cancel the station select operation Page If you have selected the traffic programme To switch the display Presetx WTo manually recall the stations stored in memory About the Ptyi Dynamic PTY Indicator Checking the stand-by mode settingTo cancel the EON stand-by mode MeaningWhen in the EON stand-by mode, press the EON button EON-TIAbout the TP and TA indicators TP indicator TA indicator MeaningRecording Differences from tape recordingsDisc writing TOC About track numbers To check the remaining time available for recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingTo record without using One-Touch Editing Apms recordingCD0MD Edit High /NORMAL Recording from the built-in radio onto a MiniDisc To record the track number whilst record- ingRecording is performed as a single track Editing What the editing function can doType of characters used Within 10 seconds, press the Enter button To create a disc nameTo erase a disc name Press the Enter button to enter the characterTo create a track name To erase a track nameName TOC Edit Enter Clear To change disc names and track namesTo add a character Example To change Besut to BestWhen both tracks have a name DivideCombine Move To combine two non-contiguous tracksExample To erase tracks one at a time EraseAll Erase To erase all of the tracks at onceTimer Operation Timer playbackTimer recording To use sleep and timer playback in combi- nation Simultaneous sleep and timer op- erationTo cancel the sleep operation To use sleep and timer recording in com- binationUsing External Units Connecting external unitsHeadphones Listening to sound from an exter- nal unit Manual recordingWhat is a MINIDISC? Symptom Possible cause Remedy TroubleshootingIf a problem occurs Mini Disc System LimitationsMD recording and playback Symptom Possible causeCD Playback Radio receptionError Messages When an error message is displayed, proceed as followsResetting the Microcom Maintenance Puter External careCare of compact discs Specifications Memo