Sharp MD-M3H operation manual Specifications

Page 51

SPECIFICATIONS

As part of our policy of continuous improvement, SHARP reserves the right to make design and speci- fication changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

● General
Power source:	AC 230 V, 50 Hz
Power
consumption:	60 W
Dimensions:	Width; 160 mm (6-5/16")
	Height; 240 mm (9-1/2")
	Depth; 300 mm (11-13/16")
	Weight: 4.4 kg (9.7 lbs.)

●MiniDisc recorder section

Type:	MiniDisc recorder
Signal readout:	Non-contact, 3-beam semi-
	conductor laser pickup
Rotation speed:	400 - 900 rpm CLV, Approx
Error correction:	ACIRC (Advanced Cross In-
	terleave	Reed-Solomon
	Code)
Quantization:	20-bit linear (A/D converter)
Coding:	ATRAC	(Adaptive
	TRansformed Acoustic Cod-
	ing)
Sampling
frequency:	44.1 kHz
Recording
method:	Magnetic modulation over-
	write method
Frequency
response:	20 - 20,000 Hz
D/A converter:	1-bit D/A converter
Wow and flutter:	Unmeasurable
	(less than 0.001% W. peak)
Signal/noise ratio: 95 dB (1 kHz)
Dynamic range:	90 dB (1 kHz)
Audio channel:	Stereo; 2 channels
	Monaural; 1 channel
	(playback only)
	(long-time recording mode)

●Compact disc player section

Type:Top open type compact disc player

Signal readout:	Non-contact, 3-beam semi-
	conductor laser pickup
Rotation speed:	200 - 500 rpm CLV, Approx.
Error correction:	CIRC (Cross Interleave Reed-
	Solomon Code)
Quantization:	16-bit linear
Frequency
response:	20 - 20,000 Hz
D/A converter:	1-bit D/A converter
Signal/noise ratio: 95 dB (1 kHz)
Dynamic range:	90 dB (1 kHz)
Wow and flutter:	Unmeasurable
	(less than 0.001% W. peak)

●Tuner section

Frequency range: FM; 87.5 - 108.0 MHz AM; 522 - 1,620 kHz

Sensitivity: FM; 2.5 μV (75 ohms unbal- anced)

AM; 650 μV/m

●Amplifier section

Output power: RMS 20 W/CH (DIN 45 324) MPO 30 W/CH (DIN 45 324)

Output terminals: Speaker; 4 ohms Headphones; 16 - 50 ohms (recommended 32 ohms)

Input terminals: AUX; 500 mV/47 kohms

●Speaker section

Type:2-way speaker system 12cm (4-3/4") woofer, 2cm (3/4") tweeter

Maximum input
power:	40 W
Rated input
power:	20 W
Impedance:	4 ohms
Dimensions:	Width; 160 mm (6-5/16")
	Height; 240 mm (9-1/2")
	Depth; 198 mm (7-7/8")
	Weight; 2.9 kg (6.4 lbs.)/each

49

Image 51

Contents MD-M3H ContentsA9903.YT Terms of GuaranteeSpecial Notes Service InformationGeneral AccessoriesPrecautions Volume controlNames of Controls and Indicators Front panelRear panel 16 17 18 19 20 21 Display windowSpeaker section MD/CD Section Remote controlPreparation for USE Aerial connectionSpeaker connection Placing the system Removing the speaker grilles Connecting the AC power leadDemo mode Speaker cushionTo change the brightness of the dis Remote controlPrecautions for battery use PlayTo change the clock time Setting the ClockTo change the time display mode To see the time displayPre-programmed equalizer Surround VolumeSound Control Extra bass X-BASSTo stop playback Compact Disc OperationCD playback To interrupt playbackMinidisc Operation MD playbackTo remove a MiniDisc Cue and review Convenient CD and MD OperationApss Auto Program Search Sys- tem Repeat and random playTo check which tracks are programmed To cancel the ApmsApms Automatic Programmable Music Selector To clear the programmed selectionsSwitching the time display Changing the display during MD playbackTime Press the ON/STAND-BY button to enter the stand- by mode TuningManual tuning Auto tuningPreset memory scan Preset tuningDisplay Mode Information provided by RDSPTY Test Alarm None To erase all of the contents of preset memory Aspm Auto Station Program MemoryTo stop the Aspm operation before it is complete To cancel the station select operation Page If you have selected the traffic programme To switch the display Presetx WTo manually recall the stations stored in memory Meaning Checking the stand-by mode settingTo cancel the EON stand-by mode About the Ptyi Dynamic PTY IndicatorEON-TI When in the EON stand-by mode, press the EON buttonTP indicator TA indicator Meaning About the TP and TA indicatorsRecording Differences from tape recordingsDisc writing TOC About track numbers To stop recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To check the remaining time available for recordingTo record without using One-Touch Editing Apms recordingCD0MD Edit High /NORMAL Recording from the built-in radio onto a MiniDisc To record the track number whilst record- ingRecording is performed as a single track Editing What the editing function can doType of characters used Press the Enter button to enter the character To create a disc nameTo erase a disc name Within 10 seconds, press the Enter buttonTo erase a track name To create a track nameExample To change Besut to Best To change disc names and track namesTo add a character Name TOC Edit Enter ClearWhen both tracks have a name DivideCombine Move To combine two non-contiguous tracksExample To erase all of the tracks at once EraseAll Erase To erase tracks one at a timeTimer playback Timer OperationTimer recording To use sleep and timer recording in com- bination Simultaneous sleep and timer op- erationTo cancel the sleep operation To use sleep and timer playback in combi- nationUsing External Units Connecting external unitsHeadphones Manual recording Listening to sound from an exter- nal unitWhat is a MINIDISC? Mini Disc System Limitations TroubleshootingIf a problem occurs Symptom Possible cause RemedyRadio reception Symptom Possible causeCD Playback MD recording and playbackWhen an error message is displayed, proceed as follows Error MessagesResetting the Microcom Maintenance Puter External careCare of compact discs Specifications Memo