HP 6634B, 6633B, 6632B, 6631B manual Error Messages C

Page 67

Error Messages - C

Selftest Errors 0 through 99 (sets Standard Event Status Register bit #3)

0No error

1Non-volatile RAM RD0 section checksum failed

2Non-volatile RAM CONFIG section checksum failed

3Non-volatile RAM CAL section checksum failed

4Non-volatile RAM STATE section checksum failed

5Non-volatile RST section checksum failed

10RAM selftest

11VDAC/IDAC selftest 1

12VDAC/IDAC selftest 2

13VDAC/IDAC selftest 3

14VDAC/IDAC selftest 4

15OVDAC selftest

80

Digital I/O selftest error

 

Device-Dependent Errors 100 through 32767 (sets Standard Event Status Register bit #3)

213

Ingrd receiver buffer overrun

216RS-232 receiver framing error

217RS-232 receiver parity error

218RS-232 receiver overrun error

220Front panel uart overrun

221Front panel uart framing

222Front panel uart parity

223Front panel buffer overrun

224Front panel timeout

401CAL switch prevents calibration

402CAL password is incorrect

403CAL not enabled

404Computed readback cal constants are incorrect

405Computed programming cal constants are incorrect

406Incorrect sequence of calibration commands

407CV or CC status is incorrect for this command

408Output mode switch must be in NORMAL position

601Too many sweep points

602Command only applies to RS-232 interface

603CURRent or VOLTage fetch incompatible with last acquisition

604Measurement overrange

67

Image 67
Contents USER’S Guide Certification Warranty InformationGeneral Safety SummarySafety Symbols EMC DeclarationPrinting History Acoustic Noise InformationTable of Contents Introduction Specifications Supplemental CharacteristicsPerforming the Calibration Procedure Entry Keys Examples of Front Panel ProgrammingFlexible system features Convenient bench-top featuresQuick Reference Front Panel At a Glance Use the Function keys and Entry keys to enter a new value Front Panel Number EntryImmediate Action Keys Front Panel AnnunciatorsFront Panel Menus At a Glance ABORt SENSe CALibrate Scpi Programming Commands At a GlanceUse the front panel Address menu to Rear Panel At a GlancePage Document Orientation General InformationGetting Started Map Options Safety ConsiderationsOptions and Accessories AccessoriesDescription Output Characteristic Damage Packaging Material InstallationCleaning InspectionBench Operation LocationRack Mounting Output Connections Connect the Power CordWire Considerations Input ConnectionsVoltage Drops Remote Sense ConnectionsMultiple Load Connections Remote Sense Connections Sense LeadsStability OVP ConsiderationsPage Digital I/O Connections FLT/INH DIGital I/O ConnectorFLT/INH Examples Pin Input/Output Description Controller ConnectionsHP-IB Interface RS-232 InterfaceTurn-On Checkout Using the KeypadIntroduction Model Voltage OV Prot Current Checkout ProcedureProcedure Display Explanation Checkout Programming ValuesPress 5, Enter Procedure Display ExplanationCase of Trouble Error MessagesLine Fuse Front Panel Description Front panel OperationEntry Keys Display AnnunciatorsRotary Control Line System Keys Function KeysSystem Keys Display Command FunctionImmediate Action Keys Function KeysScrolling Keys LOW Metering KeysDisplay Measurement HighVoltprot value Output Control KeysRST OC OT OV RI FSEntry Keys Entry KeysSet the output voltage Setting the Output Voltage and CurrentEnable the output Examples of Front Panel ProgrammingMaking Front Panel Measurements Querying and Clearing Output ProtectionAction Currrang Auto Use the Meter menu for making front panel measurementsCurrdet Acdc To configure the Digio mode of the port, proceed as follows To configure the Ridfi mode of the port, proceed as followsProgramming the Digital Output Port Set the HP-IB address as follows Setting the HP-IB Address and RS-232 ParametersConfigure the RS-232 interface as follows Programming the Output Relay option 760 onlyRecall a saved state as follows Select the power-on state of the dc source as followsSaving and Recalling Operating States Save an operating state in location 1 as followsPage Specifications Table A-2. Supplemental Characteristics Supplemental CharacteristicsDynamic Measurement Command ProcessingINH/FLT Characteristics Parameter HP 66332AShipping weight Digital I/O CharacteristicsDimensions Net weightTable B-1. Equipment Required Test SetupVerification and Calibration Equipment RequiredPerforming the Verification Tests Figure B-1. Verification & Calibration Test SetupTable B-2. Verification Programming Values Turn-On CheckoutVoltage Programming and Measurement Accuracy Current Programming and Measurement AccuracyCurrent Sink Measurement Current Measurement Low RangeCurrrang LOW Current Sink Measurement Table B- 3. Verification Test Record for HP 6631BCurrent Programming and Measurement High Range Current Measurement Low RangeTable B- 6. Verification Test Record for HP 6634B Table B- 5. Verification Test Record for HP 6633BFront Panel Calibration Menu Performing the Calibration ProcedureOvervoltage Protection Calibration Enable Calibration ModeFront Panel Calibration Voltage Programming and Measurement CalibrationNegative Current Programming Calibration Current Programming and High-Range Measurement CalibrationLow-Range Current Measurement Calibration AC Current Measurement Calibration HP 66332A only Calibration Error MessagesTable B- 7. HP-IB Calibration Error Messages Error MeaningCalibration Over the HP-IB Changing the Calibration PasswordCalpass Page Error Number List Error MessagesTable C-1. Error Numbers Error Messages Error Messages C Page Line Voltage Conversion Configure the Power TransformerOpen the Unit Close the Unit Install the Correct Line FuseIndex Index Index Latin America United States of America EuropeJapan Asia PacificManual Updates
Related manuals
Manual 94 pages 1.46 Kb

6631B, 6633B, 6634B, 6632B specifications

The HP 6632B, 6634B, 6612B, and 6633B are high-performance programmable power supplies that have gained prominence in various testing and measurement applications. These models are part of the HP 6000 series, which is renowned for its reliability and versatility in providing precision power supply solutions.

The HP 6632B offers a dual-output capability, delivering up to 32 volts and 3 amps per channel. It is designed for applications requiring stable and accurate voltage and current supplies. With features like overvoltage protection and short-circuit protection, it ensures the safety of both the device under test and the power supply itself. The programmable voltage and current settings allow operators to automate their testing procedures, increasing efficiency.

The HP 6634B takes performance a step further with multiple outputs, providing up to 32 volts and 5 amps per channel. This model is particularly suited for applications requiring higher current, especially in battery testing and device characterization. The ability to program the device remotely adds an extra layer of usability, making it ideal for integration into automated testing environments.

The HP 6612B model is tailored for users who require a compact and portable power supply solution. It delivers up to 20 volts and 2 amps. Despite its smaller size, it retains essential features like programmable settings and fast transient response, making it suitable for both educational purposes and field testing scenarios.

For users looking for a versatile, multi-channel solution, the HP 6633B presents itself as an excellent choice. This model offers up to 32 volts and 5 amps across multiple outputs. It supports a wide range of programmable features and has an intuitive interface, making it user-friendly for both beginners and experienced engineers. The robust design of the 6633B ensures reliable performance in demanding environments.

All four models utilize advanced linear power supply technology that minimizes ripple and noise, which is critical for sensitive electronic components. Together, these power supplies provide professionals in research, manufacturing, and testing with the precision they need for their experiments and product developments. The combination of programmability, safety features, and high-performance specifications makes the HP 6632B, 6634B, 6612B, and 6633B essential tools for electronic engineers and technicians.