HP SuperStack 3 Load Balancer Appliance Click Next. The Server Subnet Define Subnet page appears

Page 62

62CHAPTER 8: CONFIGURING FOR LOAD BALANCING

Defining a Server Before you can add a server, you need to have defined at least one server

Subnetsubnet. The default gateway of each server must be set to the floating default gateway address of the Server Load Balancer.

To define a server subnet, complete the following steps:

1Click Logical View on the Toolbar.

2From the Navigation tree, select Server Load Balancing > Setup -> Server Subnets.

3Click Add. The first wizard page appears.

4Click Next. The Server Subnet - Define Subnet page appears.

5Enter 192.168.2.254 in the IP Address field.

If configuring for a redundant configuration, you need to enter the IP addresses of both Device A and Device B.

6Enter 255.255.255.0 in the Subnet Mask field.

7Click Next. The Server Subnet - Device A Floating Address page appears

8Complete the entry in the Floating Address field. For example,

192.168.2.200.

Do not forget to change the default gateway on your servers to this IP address

9Click Finish. Your server subnet has been added.

Image 62

Contents SuperStack 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Setting UP for Management Technical Specifications and PIN-OUTS 3Com Knowledgebase Web Services About this Guide Convention Description ConventionsIcon Description Registration Related DocumentationProduct DocumentationAbout this Guide Balancer Server Load Balancer Feature Server Load Balancer Plus MemoryFeature Server Load Balancer Plus Algorithms 12 10/100 LAN PortsServer Load Balancer Front View Detail10/100BASE-T Port Status LEDs Color Indicates Power/Self Test LEDPower LED 1000BASE-SX Port Status LEDsPower Socket Balancer Rear View DetailDocumentation shipped with the power system Advanced Redundant Power System outputType 3 Power Module, read the Safety Information section Disconnecting the power cordInstalling the Server Load Installing the Server Load Balancer Rack-mounting Server Load Balancer if they have been fittedPlacing Units On ChoosingCorrect Cables Top of Each OtherSequence Power-upPowered-up and ready for operation Problem Suggested Solution On powering-up, the Power/Self Test LED lights yellowSetting UP for Management Address Methods Managing Server Load BalancerAssigning an IP SEC Setting UP for Management Interface Security Warning Window To install the plug-in, complete the following steps Web Interface pages appearsAfter a management session Network Password window appearsInterfacesteps Banner Using the Web InterfaceWeb interface is made up of three areas Navigation TreeDevice Summary Summary information is displayed in a two tablesSystem Summary Port Hotspots Unit HotspotControl Buttons Color ActionLogical View Button Action Help View Management Setting up SnmpTrap Community String field is defaulted to public SpecifyingLoad Balancer UpgradingOperating Software Working with the WEB Interface Server Load Balancing Example ConfigurationBalancing Approximately double the performance of Server BConfiguring for Non-redundant Server Load Balancing Click Next. The Getting Started Password page appears Configuring Redundant Load Balancing Balancer 1 and is configured for the same serviceRedundant Server Redundancy Configuring forActive-Passive Load Balancer for active-passive redundancyEnter 10.20.30.56 in the Device B IP Address field Active-Active Load Balancer for active-active redundancyClick Next. The Getting Started IP Settings page appears Enter 25 in the Virtual router ID a field SettingSettings Enter 26 in the Virtual router ID B fieldConfiguring Redundant Server Load Balancing Redirection Cache Redirection Configuration Example Subnet ConfigurationDefining a Cache Non-redundantClick Next Click Finish. Your cache subnet has been added Assigning Caches to ServicesAdding a Cache Been createdSteps Enter a descriptive name, such as Cache2, in the Name fieldSupported Algorithms Description Destination Weighted Round RobinWeighted Least Round RobinThis sets the number of retries a health check is attempted TimeoutRetries field Balancing Click Next. The Server Subnet Define Subnet page appears Click Finish. Your server subnet has been addedChanging Lan Port Roles Adding a Server Highlight Http and click the Next Click Continue with Advanced SettingsEnter a descriptive name, such as Web, in the Name field Assigning Servers To ServiceServer load balancing service Showing StatusEnter 8080 in the Server port field Click OK Click Server AssignmentsClick on the cell next to Server A. a pop-up menu appears This user group Adding a UserGroup To add a user group, complete the following stepsTo assign permissions, complete the following steps Click PermissionsQuickest Average Supported Algorithms Description Round RobinQuickest Last Response ResponseThis sets the number of retries in a health check period Filters Select the attack filters you wish to enable and click OKMitigation Filter DescriptionSelect Security User Modifying Admin AccessModifying Monitor Access Configuring for Load Balancing Safety Information Important Safety InformationImportant Safety Information Personnel qualifié ’information deSécurité Importante Hub plus étroites’information de Sécurité Importante Wichtige Sicherheitsinformat ionen EuropeAchtung Faseroptikanschlüsse Optische Sicherheit Appendix a Safety Information Balancer and the Server Load Balancer Plus SpecificationsPIN -OUTS Pin to RS232 25-pin Console Port CablePC-AT Serial Pin to 9-pin3Com ServicesOnline Technical Username anonymous Asia, Pacific Rim Europe, Middle East AfricaNorth America Country Telephone Number Fax Number Appendix C Technical Support Index NumbersSpecifications, system 83 summary view Summary view 32 World Wide Web WWW Index Superstack 3 Server Load Balancer 3C16120 Obtaining Warranty Service Warranties Exclusive Other Services Regulatory Notices

Related manuals

Manual 20 pages 24.02 Kb