HP SuperStack 3 Load Balancer Appliance manual Select Security User, Modifying Admin Access

Page 73

Modifying Security Filters (Attack Mitigation)

73

Modifying User To modify the access of either the admin or monitor user, complete the Access following steps:

1Click Device View on the Toolbar.

2Select Security > User.

3You can modify the user access for either the admin or monitor.

Modifying Admin Access

a To modify the admin access, click Modify Admin. The Modify Password page appears.

b Enter a new password and confirm.

Modifying Monitor Access

a To modify the monitor access, click Modify Monitor. The Modify Password page appears.

b Enter a new password and confirm.

CAUTION: The Server Load Balancer does not provide a way to recover a lost password. If you choose to assign a new password, it is suggested you keep note of it in a safe place. If you forget your password, you will be locked out of the unit. If you change the password during the CLI Server Load Balancer setup, this is the password you should use, and not the blank default login password. For Technical Support, see Appendix C.

Image 73

Contents SuperStack 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Setting UP for Management Technical Specifications and PIN-OUTS 3Com Knowledgebase Web Services About this Guide Icon Description ConventionsConvention Description Product Related DocumentationRegistration DocumentationAbout this Guide Balancer Feature Server Load Balancer Plus Algorithms Feature Server Load Balancer Plus MemoryServer Load Balancer 12 10/100 LAN PortsBalancer Front View Detail Server LoadPower LED Color Indicates Power/Self Test LED10/100BASE-T Port Status LEDs 1000BASE-SX Port Status LEDsBalancer Rear View Detail Power SocketType 3 Power Module, read the Safety Information section Advanced Redundant Power System outputDocumentation shipped with the power system Disconnecting the power cordInstalling the Server Load Installing the Server Load Balancer Server Load Balancer if they have been fitted Rack-mountingCorrect Cables ChoosingPlacing Units On Top of Each OtherPowered-up and ready for operation Power-upSequence On powering-up, the Power/Self Test LED lights yellow Problem Suggested SolutionSetting UP for Management Assigning an IP Methods Managing Server Load BalancerAddress SEC Setting UP for Management Interface Security Warning Window Web Interface pages appears To install the plug-in, complete the following stepsInterfacesteps Network Password window appearsAfter a management session Web interface is made up of three areas Using the Web InterfaceBanner Navigation TreeSystem Summary Summary information is displayed in a two tablesDevice Summary Unit Hotspot Port HotspotsColor Action Control ButtonsLogical View Button Action Help View Trap Community String field is defaulted to public Setting up SnmpManagement SpecifyingOperating Software UpgradingLoad Balancer Working with the WEB Interface Server Load Balancing Balancing ConfigurationExample Approximately double the performance of Server BConfiguring for Non-redundant Server Load Balancing Click Next. The Getting Started Password page appears Configuring Redundant Redundant Server Balancer 1 and is configured for the same serviceLoad Balancing Active-Passive Configuring forRedundancy Load Balancer for active-passive redundancyEnter 10.20.30.56 in the Device B IP Address field Load Balancer for active-active redundancy Active-ActiveClick Next. The Getting Started IP Settings page appears Settings SettingEnter 25 in the Virtual router ID a field Enter 26 in the Virtual router ID B fieldConfiguring Redundant Server Load Balancing Redirection Cache Redirection Configuration Example Defining a Cache ConfigurationSubnet Non-redundantClick Next Click Finish. Your cache subnet has been added Adding a Cache ServicesAssigning Caches to Been createdEnter a descriptive name, such as Cache2, in the Name field StepsWeighted Least Weighted Round RobinSupported Algorithms Description Destination Round RobinRetries field TimeoutThis sets the number of retries a health check is attempted Balancing Click Finish. Your server subnet has been added Click Next. The Server Subnet Define Subnet page appearsChanging Lan Port Roles Adding a Server Enter a descriptive name, such as Web, in the Name field Click Continue with Advanced SettingsHighlight Http and click the Next Server load balancing service To ServiceAssigning Servers Showing StatusClick on the cell next to Server A. a pop-up menu appears Click Server AssignmentsEnter 8080 in the Server port field Click OK Group Adding a UserThis user group To add a user group, complete the following stepsClick Permissions To assign permissions, complete the following stepsQuickest Last Response Supported Algorithms Description Round RobinQuickest Average ResponseThis sets the number of retries in a health check period Mitigation Select the attack filters you wish to enable and click OKFilters Filter DescriptionModifying Monitor Access Modifying Admin AccessSelect Security User Configuring for Load Balancing Safety Information Information Important SafetyImportant Safety Information Sécurité Importante ’information dePersonnel qualifié Hub plus étroites’information de Sécurité Importante Europe Wichtige Sicherheitsinformat ionenAchtung Faseroptikanschlüsse Optische Sicherheit Appendix a Safety Information PIN -OUTS SpecificationsBalancer and the Server Load Balancer Plus PC-AT Serial Console Port CablePin to RS232 25-pin Pin to 9-pinOnline Technical Services3Com Username anonymous Europe, Middle East Africa Asia, Pacific RimNorth America Country Telephone Number Fax Number Appendix C Technical Support Numbers IndexSpecifications, system 83 summary view Summary view 32 World Wide Web WWW Index Superstack 3 Server Load Balancer 3C16120 Obtaining Warranty Service Warranties Exclusive Other Services Regulatory Notices

Related manuals

Manual 20 pages 24.02 Kb