HP m300 manual Removing the Tray

Page 35

Tray

The tray is used to align the computer on the expansion base. The left side of the computer should be aligned with the left side of the tray when docking the computer.

1.Prepare the expansion base for disassembly (Section 5.3).

2.Position the expansion base so the front faces forward.

3.Remove the label ➊ and screw ➋ located behind the retaining latch ➌ (Figure 5-5).

4.Pull forward ➍ on the retaining latch to remove the tray.

Figure 5-5.Removing the Tray

Reverse the removal procedure described above to install the tray.

Removal and Replacement Procedures

5-5

Image 35

Contents Compaq ArmadaStation EM Maintenance and Service Guide Contents Appendix Technician Notes Using this GuideSymbols Locating Additional Information Serial NumberProduct Description ArmadaStation EM FeaturesExternal Connectors Security FeaturesDescription Function ArmadaStation EM ComponentsArmadaStation EM Front Components ArmadaStation EM Right Side Components Volume control switchArmadaStation EM Rear Panel Components ArmadaStation EM Rear Panel ComponentsDevice Activity LightsMultiBays MultiBay/Device CompatibilityPCI Expansion Boards Half-Height BaySecurity Lock Before Replacing Parts TroubleshootingProblem Probable Cause Recommended Actions Problems and SolutionsSolving Docking and Undocking Problems Solving Expansion Board ProblemsSolving Expansion Device Installation Problems Solving External Keyboard ProblemsSolving External Mouse Problems Press any key or click the mouse Solving External Monitor ProblemsSerial Number Location Illustrated Parts CatalogCompaq ArmadaStation EM Components Compaq ArmadaStation EM ComponentsDescription Spare Parts Compaq ArmadaStation EM ComponentsItem Description Plastics Kit ComponentsPlastics Kit Components Spare Part Number MultiBay Option Cable Kit Components Spare Part Number MultiBay Option Cable KitSpare Part Number MiscellaneousSpare Parts Miscellaneous not illustrated Electrostatic Discharge Removal and Replacement PreliminariesRelative Humidity Event 10% 40% 55% Generating StaticPreventing Electrostatic Damage to Equipment Typical Electrostatic VoltagesMethod Preventing Damage to DrivesGrounding Methods Static Shielding Protection LevelsGrounding Equipment Grounding WorkstationsRecommended Materials and Equipment Screws Service ConsiderationsTool and Software Requirements Plastic Parts Cables and ConnectorsRemoval and Replacement Procedures Expansion Base Disassembly Sequence Disassembly Sequence ChartDisconnecting the Expansion Base Preparing the Expansion Base for DisassemblyExpansion Base Feet External ComponentsRemoving the Tray TrayRemoving the Connector Cover Connector CoverRemoving the Rear Bezel Rear BezelSliding the Manual Release Lever Locating the Expansion Slots PCI Expansion Boards10.Removing the Expansion Slot Cover 11.Installing an Expansion Board 12.Removing the Top Cover Screws Top CoverSwing the top cover up and forward to remove it Figure Half-Height Bay Installing a Half-Height Drive15.Removing the Half-Height Bay Blank Bezel Cover 16.Removing the Half-Height Drive Screws 17.Attaching the Bezel Cage to the Half-Height Drive 18.Connecting the Power Cable 19.Connecting the Diskette Drive Cable 20.Connecting the Hard Drive Cable 21.Connecting the CD-ROM Drive/Audio Cable 22.Installing a Half-Height Drive 23.Removing the Left Speaker Left SpeakerMultiBay 24.Disconnecting the Half-Height Bay and Left Speaker Cables25.Removing the MultiBay and Control Panel 26.Removing the Control Panel Control PanelMechanism Assembly 28.Removing the Mechanism Assembly Power Supply 30.Removing the Power Supply 31.Removing the Backplane BackplaneMetric Expansion Base Physical and Environmental SpecificationsPecifications 2Specifications Table A-2 Microphone Jack Connector PIN AssignmentsTable A-1 Headphone Jack Table A-4 Table A-5 Serial ConnectorTable A-3 Table A-8 Stereo Line-in Jack Table A-6Table A-7 Stereo Line-out Jack Signal Pin Table A-13 Docking ConnectorPDATA6 LD14 Pin Signal General Requirements Power Cord SET RequirementsConductor Power Cord Set Country Accredited Agency Applicable Note Numbers Conductor Power Cord Set Requirements-By CountryCountry-Specific Requirements Index PCI Index

Related manuals

Manual 13 pages 51.21 Kb