HP 28642A manual Part number...2-3 Field replaceable units se-eFRUS, FRUs...2-3

Page 62

electrical specifications..216 electromagnetic specifications..2-16 environmental specifications..516 exchangeassembly

part number...2-3

F

field replaceable units se-eFRUS

filler card...l-14 removing...l-15

FRUs...2-3

part numbers...2-4 fuse...24

removaUreplacement...2-12 TERMF’WR LED...2-6

H

hardware address...l-13 configuration...l-7

HP Precision Bus

SeeHP-PB HP-PB

specitications,..l-12 HP-UX system...2-15 configuration...127

I

identification information...l-4 installing

adapter card...l-11 resistor packs...l-10

Index - 3

Image 62

Contents HP 28642A HP-PB Scsi HP 28655A HP-PB SCSI/ Parallel HP HP 5960-3126 El091Print History Safety Considerations@Hewlett-Packard Company, 1991. AI1rights rcservcd Installation and S&vice HP 28642A and HP 28655A at a Glance Product Description This Book Table of Contents Page Installing HP 28642A/28655AAdapter Lnstalllng the HP 28642A/28655A Adapter Verify Product Contents Prepare to Install the Adapter CardObserve Antlstatic Precautions Gather Tools and Accessories Needed Record Adapter Card Identification InformationTable l-l. Scsi Cables LengthsDescription meters Dependent requirements that are not noted herePeripheral to 92222A Remove Data corruption Installing the AdapterShut Down the System and SwZtch Off the Computer CreateCheck the Card’s Hardware Configuration Figure l-4. Default Switch Settings Installing the Adapter Set the Desired Parity-Checking CapabUityScsi Bus = closed = open Installing the Adapter l-9Set the Scsi Bus Address AddressVerify that Resistor Packs are Properly Installed Two resistor packsmust be installedInstall and Connect the Card Select an Appropriate SlotHP-Pa Standard Power Symbol Systemperformance implications, if any Record the Slot NumberComputer hardware limitations for l/O cards, if any Prepare the Slot For Use Ignment Hole Page Card guides. If the problem persists,get help Insert the Card into the SlotSupplied with this product provides a thumbscrew connector Attach the Card CablesConnect Your Single-Ended Scsi Devices Installing the Adapter l-19Connect Your Peripheral Devices Properly on the SCSIbusTerminate the Scsi Bus Device operation on the SCSIbus 12. Scsi Bus Example Installing the Adapter Scsi Cable Length ExampleReassemble your computer TurnPowerOn to Peripherals, Then to the ComputerConnect Your Parallel Device, If Applicable Two metersIn/Out Signal Name24Installing the Adapter Pin25 Turn Power On to Peripherals, Then to the Computer Data corruption or loss,or damageto hardwareMPE XL Systems Set Up the Operating SystemHP-UX Systems Verify Operation ServiceInformation Service Information Field Replaceable Units Exchange AssemblyExchange adapter card assembly Flgure 2-1. Location of Board Component FRUsBoard Components Other FRUsSelf-lestFailure Troubleshooting ToolsShould be performed by authorized servicepersonnel only Operation. Refer to your systemreference manuals Boot failure occursSelf-Test Failure LED Scsipba and Centpba Diagnostics Troubleshooting ChecklistDoes any device require a special SCSIterminator? Removal/Replacement Instructions Removal/Replacement of the Card For card removal, follow the procedures belowAlso be determined from the,scsipbadiagnostic Removal/Replacement of Card ComponentsMinimize touching the connector pins Service Information 2-lDamagewasextensive, you may need a new component Type and ratingCan continue to operate normally DiagnosticFlgure 2-3. Replacing the Termpwr Fuse Service Information Reshipment Guidelines 1green Technical SpecificationsGeneral IElectrical +5 Vdc IPhysical IEnvironmentalAmerican National StandardsInstitute Backplane ConfigurationGlossary FRU Host adapter Seeadapter HP-PBPrecision Bus See HP-PB Complies with the Scsi specification X3.131 GlossaryParallel port SCSI-2 Termination Index Index tCable Card version...14FRUs...2-3 Identification information...l-4 installingPart number...2-3 Field replaceable units se-eFRUS HP Precision Bus SeeHP-PB HP-PBPhysical specifications...2-16 Index Loopback hood...2-4Resistor pack...&10 PowerProduct contents...13 Self-test failure LED...2-6 shut downTroubleshooting..2-8 Storing adapter cards...l-3 switchDuring installation/removal..J-6,1-19,2-10 Ylrlbo~5960-3126 El091