Setting the remote controller | Toshiba RAS-10SAVP-E, RAS-B13SKVP-E

	Item	Operation flow and applicable data, etc.			Description

17. Select switch on					1. Purpose
	remote controller				This operation is to operate only one
					This operation is to operate only one
					indoor unit using one remote controller.
					indoor unit using one remote controller.
					2. Description
	Push the operation button				2. Description
	Push the operation button				When operating one indoor unit in a
	on the remote controller.				situation where two indoor units have
					situation where two indoor units have
					been installed in the same room or
					been installed in the same room or
					nearby rooms, this operation prevents the
					remote controller signal from being
				Select “B” as the setting for	remote controller signal from being
	Both indoor units		YES	Select “B” as the setting for	received simultaneously by both units,
	Both indoor units		YES	one of the two indoor units and	thus preventing both units from operating.
	start operation.			for the remote controller.	thus preventing both units from operating.
	start operation.			for the remote controller.
	NO			(See below for details.)	3. Operation
					The indoor unit on which the remote
					The indoor unit on which the remote
					controller selection has been set to B
					controller selection has been set to B
	Unnecessary set				receives the signal of the remote control-
	Unnecessary set				ler also set to B.
	[Remote controller select]				(At the factory the remote controller
					(At the factory the remote controller
					selection is set to A on all the indoor
					selection is set to A on all the indoor
					units. There is no A setting display.)

HiPOWER	SLEEP MODE		MEMO
			1.3.5.9H
SWING	FIX	FAN	OFF	Jumper wire
CLR			SET
CLOCK	ON	OFF
CLOCK
RESET
	CHECK

Cutting direction

When switching between settings “A” and “B”, always switch the indoor unit board and the remote controller as a pair. (Otherwise, the indoor unit will not accept the remote controller’s signals.)

1.Setting the remote controller

Q Slide and open the remote controller cover and remove the batteries.

R Cut the jumper wire inside the battery compartment using nippers.

•The jumper wire should not remain in contact after being cut. Also be careful not to let plastic scraps, jumper wire cuttings or other debris enter the inside of the remote controller.

SInsert the batteries. “B” appears in the remote controller display.

*Even after the jumper wire has been cut, switching between A and B is still possible by pushing the CHECK button and FIX button together.

The A or B setting, which was switched by pushing the CHECK button and FIX button together, is restored to the setting established prior to the switching when the battery is replaced or the RESET button is pushed.

2.Setting the unit

Push the RESET button (Indoor unit) to start automatic operation.

3.Push the button of the remote controller that was set in step 1 to stop the air conditioner.

(This operation will change the setting to “B”.)

4.Check that the remote controller operates the indoor unit.

– 44 –

RAS-10SAVP-E, RAS-B10SKVP-E, RAS-B13SKVP-E specifications

Toshiba has established itself as a leader in the HVAC market, known for its innovative technologies and reliable performance. Among its range of air conditioning units, the Toshiba RAS-B10SKVP-E, RAS-10SAVP-E, and RAS-B13SKVP-E models stand out for their efficiency and advanced features.

The Toshiba RAS-B10SKVP-E is designed for optimal cooling and heating efficiency, making it an ideal choice for small to medium-sized rooms. One of its main features is the Super Hi-M-PAM inverter technology, which enhances energy savings by continuously adjusting the compressor speed to match the cooling demand. This results in lower energy consumption while maintaining a stable temperature. Additionally, the unit boasts a 4-in-1 operation mode that allows users to select cooling, heating, dehumidification, or ventilating modes, ensuring maximum comfort at all times.

Similarly, the RAS-10SAVP-E model incorporates advanced features such as an eco-friendly refrigerant, R32, which has a lower Global Warming Potential (GWP) compared to traditional refrigerants. This model is equipped with a high-efficiency filter that captures dust and allergens, ensuring cleaner air quality. The sleek design allows for easy integration into various interior styles, while its quiet operation makes it a preferred choice for residential environments.

The RAS-B13SKVP-E model takes performance to the next level with a robust cooling capacity, designed for larger spaces. This model utilizes Toshiba's unique DC Hybrid Inverter technology, which not only enhances cooling efficiency but also facilitates faster temperature control. A notable characteristic of this unit is its wide-angle air distribution system, which allows for even airflow throughout the room, enhancing comfort.

In addition to these features, all three models are equipped with smart controls that enable users to operate their air conditioning systems remotely via mobile devices. This connectivity adds convenience and ensures that users can manage their indoor climate at their fingertips. They also come with user-friendly interfaces and programmable timers, allowing for personalized comfort settings.

In conclusion, the Toshiba RAS-B10SKVP-E, RAS-10SAVP-E, and RAS-B13SKVP-E air conditioning units combine energy efficiency, innovative technology, and user-friendly features to deliver exceptional indoor comfort. With their advanced technologies, these models are ideal choices for anyone seeking reliable and effective climate control solutions.

Operation flow and applicable data, etc.

1. Purpose

3. Operation

units. There is no A setting display.)

1.Setting the remote controller

2.Setting the unit

RAS-10SAVP-E, RAS-B10SKVP-E, RAS-B13SKVP-E specifications