19BAUMATIC BDW13, BDW14 dishwasher user manual
BEFORE YOU CALL FOR SERVICE …
CHECKING AGAINST THE CHARTS BELOW MAY FIX YOUR PROBLEM.
PROBLEM |
| POSSIBLE CAUSES |
| WHAT TO DO |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Dishwasher doesn’t run!
•Replace fuse or reset circuit breaker.
•Fuse blown, or the
| circuit breaker acted |
| • Remove any other appliances |
| |
|
|
| feeding from the same socket as |
| |
|
|
| the dishwasher. |
| |
|
|
|
|
| |
|
|
|
|
| |
|
|
|
|
| |
• Power supply is not |
| • Make sure the dishwasher is turned |
|
| |
| turned on |
| on and the door is closed securely. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Water pressure is low |
| • Check that the water supply is |
|
| |
| connected properly and the water is |
|
| ||
|
|
| turned on. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• | … And (situation A) |
| • For situation A, Press and hold |
|
|
| the number 17 is |
| down the Delay Timer key at the |
|
|
| showing on the |
| same time as you’re pressing the |
|
|
|
| ‘ON/OFF’ button to switch the |
|
| |
| display. This means |
|
|
| |
|
| dishwasher off. Wait a few |
|
| |
| that your dishwasher |
|
|
| |
|
| seconds then press only the |
|
| |
| has entered Test |
|
|
| |
|
| ‘ON/OFF’ button again. You are |
|
| |
| Mode – a factory |
|
|
| |
|
| now ready to program your |
|
| |
| sequence which you |
|
|
| |
|
| dishwasher for a washing cycle as |
|
| |
| need not concern |
|
|
| |
|
| per usual. |
|
| |
| yourself with. This |
|
|
| |
|
|
|
|
| |
| happens because the |
|
|
|
|
| Delay Timer key was |
|
|
|
|
| pressed before the |
|
|
|
|
| ‘ON/OFF’ key was |
|
|
|
|
| pressed. |
|
|
|
|
|
|
| • For situation B, Press ‘ON / OFF’ |
|
|
|
|
| button to turn the dishwasher off. |
|
|
|
|
| Then, press and hold down the |
|
|
|
|
| Program Key (‘P’) at the same |
|
|
• | … Or (situation B) |
| time as you’re pressing the ‘ON / |
|
|
| OFF’ button to switch the |
|
| ||
| the display shows one |
| dishwasher on again. You are now |
|
|
| of the following: 0A, |
| ready to program a cycle as per |
|
|
| 09, 08, 07, 06, 05, |
|
|
| |
|
| usual. |
|
| |
| 04, 03, 02, 01, 00. |
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
Drain Pump doesn’t stop!
•Overflow
•The system is designed to detect an overflow. When it does, it shuts off the circulation pump and turns on the drain pump. Call a Baumatic Ltd approved technician.
19