ASRock P67 Extreme4 Gen3 manual Select Nvidia Control Panel tab, Select Control Panel tab

Page 25

For Windows® VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS: (For SLITM and Quad SLITM mode)

A. Click the Start icon on your Windows taskbar.

B. From the pop-up menu, select All Programs, and then click NVIDIA Corporation.

C. Select NVIDIA Control Panel tab.

D. Select Control Panel tab.

E. From the pop-up menu, select Set SLI and PhysX configuration. In Set PhysX GPU acceleration item, please select Enabled. In Select an SLI configuration item, please select Enable SLI. And click Apply.

F. Reboot your system.

G. You can freely enjoy the benefit of SLITM or Quad SLITM feature.

*SLITM appearing here is a registered trademark of NVIDIA® Technologies Inc., and is used only for identification or explanation and to the owners’ benefit, without intent to infringe.

25

Image 25
Contents P67 Extreme4 Gen3 Disclaimer Copyright NoticeContents Utilities Menu Introduction Uefi Menu BarIntroduction Package ContentsSpecifications Smart Switch ConnectorUSB3.0 Unique Feature Bios FeatureSupport CD HardwarePage Page Page 24.4cm 9.6 Motherboard LayoutLAN Port LED Indications I/O PanelTable for Audio Output Connection Page Screw Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Configurations Installation of Memory Modules DimmNotch break Break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie slots Requirements Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupDouble-click Nvidia Settings icon on your Windows taskbar Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS Install the required drivers to your systemFor Windows 7 / VistaTM OS Page Jumpers Setup Surround Display Feature\ Surround Display Information DescriptionOnboard Headers and Connectors USB 3.0 Header USB 2.0 HeadersSeveral system front panel System Panel HeaderFunctions Speaker to this header Chassis Speaker HeaderSupply to this connector ATX Power Connector Please connect an ATX powerATX 12V Power Connector Serial port Header Installation Guide of Front USB 3.0 PanelSerial port module Smart Switches Installation Guide of Rear USB 3.0 BracketStatus Code Description 13 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation What is Hot Swap Function? What is Hot Plug Function?Hot Plug and Hot Swap Functions for Sata / Sataii HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Unplug Points of attention, before you process the Hot PlugInstalling Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi Make a Sata / Sataii / SATA3 Driver DisketteUse RAID Installation Guide to set RAID configuration Setting Up a RAID Ready SystemMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen OC Tweaker Screen RAS# to CAS# Delay tRCD Dram Timing Control Dram Configuration Load XMP SettingCommand Rate CR Write Recovery Time tWRWrite to Read Delay tWTR RAS to RAS Delay tRRDMemory Fast Boot Memory Power Down ModeUse this to select Vccsa Voltage. The default value is Auto Use this to select VTT Voltage. The default value is AutoUser Default VTT VoltageInstant Flash Advanced ScreenCPU Configuration Intel Virtualization Technology CPU Thermal ThrottlingNo-Excute Memory Protection Local x2APICLow Mmio Align North Bridge ConfigurationVT-d Primary Graphics AdapterSouth Bridge Configuration Onboard Debug Port LED Marvell SATA3 Operation Mode Storage ConfigurationMarvell SATA3 Bootable Sata ModeSuper IO Configuration Acpi Configuration USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Contact Information Software SupportInstalling OS on a HDD Larger Than 2TB