ASRock P67 Extreme4 Gen3 manual Advanced Screen, Instant Flash

Page 60

3.4 Advanced Screen

In this section, you may set the configurations for the following items: CPU Configu- ration, North Bridge Configuration, South Bridge Configuration, Storage Configura- tion, Super IO Configuration, ACPI Configuration and USB Configuration.

Setting wrong values in this section may cause the system to malfunction.

Instant Flash

Instant Flash is a UEFI flash utility embedded in Flash ROM. This conve- nient UEFI update tool allows you to update system UEFI without entering operating systems first like MS-DOS or Windows®. Just launch this tool and save the new UEFI file to your USB flash drive, floppy disk or hard drive, then you can update your UEFI only in a few clicks without prepar- ing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the UEFI files and their respective information. Select the proper UEFI file to update your UEFI, and reboot your system after UEFI update process completes.

60

Image 60
Contents P67 Extreme4 Gen3 Copyright Notice DisclaimerContents Introduction Uefi Menu Bar Utilities MenuPackage Contents IntroductionSpecifications Connector Smart SwitchUSB3.0 Bios Feature Unique FeatureSupport CD HardwarePage Page Page Motherboard Layout 24.4cm 9.6I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Pre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch break BreakInstalling an expansion card Expansion Slots PCI and PCI Express SlotsPcie slots Slitm and Quad Slitm Operation Guide RequirementsASRock SLIBridge2S Card Driver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlyDouble-click Nvidia Settings icon on your Windows taskbar Select Nvidia Control Panel tab Select Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge Install the required drivers to your system For Windows XP OSFor Windows 7 / VistaTM OS Page Surround Display Feature Jumpers Setup\ Surround Display Information DescriptionOnboard Headers and Connectors USB 2.0 Headers USB 3.0 HeaderSystem Panel Header Several system front panelFunctions Chassis Speaker Header Speaker to this headerATX Power Connector Please connect an ATX power Supply to this connectorATX 12V Power Connector Installation Guide of Front USB 3.0 Panel Serial port HeaderSerial port module Installation Guide of Rear USB 3.0 Bracket Smart Switches13 Dr. Debug Status Code DescriptionPage Page Page Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function? What is Hot Swap Function?Hot Plug and Hot Swap Functions for Sata / Sataii HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Plug Points of attention, before you process the Hot UnplugDriver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Make a Sata / Sataii / SATA3 Driver DisketteSetting Up a RAID Ready System Use RAID Installation Guide to set RAID configurationMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Introduction Uefi Menu BarNavigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen OC Tweaker Screen Dram Timing Control Dram Configuration Load XMP Setting RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRRAS to RAS Delay tRRD Write to Read Delay tWTRMemory Fast Boot Memory Power Down ModeUse this to select VTT Voltage. The default value is Auto Use this to select Vccsa Voltage. The default value is AutoUser Default VTT VoltageAdvanced Screen Instant FlashCPU Configuration CPU Thermal Throttling Intel Virtualization TechnologyNo-Excute Memory Protection Local x2APICNorth Bridge Configuration Low Mmio AlignVT-d Primary Graphics AdapterSouth Bridge Configuration Onboard Debug Port LED Storage Configuration Marvell SATA3 Operation ModeMarvell SATA3 Bootable Sata ModeSuper IO Configuration Acpi Configuration USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Contact InformationInstalling OS on a HDD Larger Than 2TB