ASRock P67 Extreme4 Gen3 manual USB3.0, Connector, Smart Switch

Page 7

 

- 1 x Optical SPDIF Out Port

 

- 6 x Ready-to-Use USB 2.0 Ports

 

- 1 x eSATA3 Connector

 

- 2 x Ready-to-Use USB 3.0 Ports

 

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

 

LED)

 

- 1 x IEEE 1394 Port

 

- 1 x Clear CMOS Switch with LED

 

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

 

Line in/Front Speaker/Microphone (see CAUTION 5)

SATA3

- 2 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0,

 

RAID 1, RAID 10, RAID 5 and Intel Rapid Storage), NCQ,

 

AHCI and "Hot Plug" functions

 

- 2 x SATA3 6.0 Gb/s connectors by Marvell SE9120,

 

support NCQ, AHCI and "Hot Plug" functions

 

(SATA3_M2 connector is shared with eSATA3 port)

USB3.0

- 2 x Rear USB 3.0 ports by Etron EJ168A, support USB 1.0/

 

2.0/3.0 up to 5Gb/s

 

- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports) by

 

Etron EJ168A, supports USB 1.0/2.0/3.0 up to 5Gb/s

Connector

- 4 x SATA2 3.0 Gb/s connectors, support RAID (RAID 0,

 

RAID 1, RAID 10, RAID 5 and Intel Rapid Storage), NCQ,

 

AHCI and Hot Plug functions

 

- 4 x SATA3 6.0Gb/s connectors

 

- 1 x Floppy connector

 

- 1 x IR header

 

- 1 x COM port header

 

- 1 x HDMI_SPDIF header

 

- 1 x IEEE 1394 header

 

- 1 x Power LED header

 

- CPU/Chassis/Power FAN connector

 

- 24 pin ATX power connector

 

- 8 pin 12V power connector

 

- SLI/XFire power connector

 

- Front panel audio connector

 

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

 

- 1 x USB 3.0 header (supports 2 USB 3.0 ports)

 

- 1 x Dr. Debug (7-Segment Debug LED)

Smart Switch

- 1 x Clear CMOS Switch with LED

 

- 1 x Power Switch with LED

 

- 1 x Reset Switch with LED

7

Image 7
Contents P67 Extreme4 Gen3 Disclaimer Copyright NoticeContents Utilities Menu Introduction Uefi Menu BarIntroduction Package ContentsSpecifications Smart Switch ConnectorUSB3.0 Hardware Bios FeatureUnique Feature Support CDPage Page Page 24.4cm 9.6 Motherboard LayoutLAN Port LED Indications I/O PanelTable for Audio Output Connection Page Screw Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Configurations Installation of Memory Modules DimmNotch break Break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie slots Requirements Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupDouble-click Nvidia Settings icon on your Windows taskbar Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS Install the required drivers to your systemFor Windows 7 / VistaTM OS Page Description Surround Display FeatureJumpers Setup \ Surround Display InformationOnboard Headers and Connectors USB 3.0 Header USB 2.0 HeadersSeveral system front panel System Panel HeaderFunctions Speaker to this header Chassis Speaker HeaderSupply to this connector ATX Power Connector Please connect an ATX powerATX 12V Power Connector Serial port Header Installation Guide of Front USB 3.0 PanelSerial port module Smart Switches Installation Guide of Rear USB 3.0 BracketStatus Code Description 13 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Hot Plug and Hot Swap Functions for SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for Sata / Sataii HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Unplug Points of attention, before you process the Hot PlugMake a Sata / Sataii / SATA3 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up UefiUse RAID Installation Guide to set RAID configuration Setting Up a RAID Ready SystemMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen OC Tweaker Screen Write Recovery Time tWR Dram Timing Control Dram Configuration Load XMP SettingRAS# to CAS# Delay tRCD Command Rate CRMemory Power Down Mode RAS to RAS Delay tRRDWrite to Read Delay tWTR Memory Fast BootVTT Voltage Use this to select VTT Voltage. The default value is AutoUse this to select Vccsa Voltage. The default value is Auto User DefaultInstant Flash Advanced ScreenCPU Configuration Local x2APIC CPU Thermal ThrottlingIntel Virtualization Technology No-Excute Memory ProtectionPrimary Graphics Adapter North Bridge ConfigurationLow Mmio Align VT-dSouth Bridge Configuration Onboard Debug Port LED Sata Mode Storage ConfigurationMarvell SATA3 Operation Mode Marvell SATA3 BootableSuper IO Configuration Acpi Configuration Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Contact Information Software SupportInstalling OS on a HDD Larger Than 2TB