ASRock P67 Extreme4 Gen3 manual Points of attention, before you process the Hot Plug

Page 47

How to Hot Plug a SATA / SATAII / SATA3 HDD:

Points of attention, before you process the Hot Plug:

Please do follow below instruction sequence to process the Hot Plug, improper procedure will cause the SATA / SATAII / SATA3 HDD damage and data loss.

Step 1

Please connect SATA power cable 1x4-pin end (White) to the power supply 1x4-pin cable.

Step 2

Connect SATA data cable to

the motherboard’s SATAII / SATA3 connector.

SATA power cable 1x4-pin power connector (White)

Step 3

Connect SATA 15-pin power cable connector (Black) end to SATA / SATAII / SATA3 HDD.

Step 4

Connect SATA data cable to

the SATA / SATAII / SATA3 HDD.

How to Hot Unplug a SATA / SATAII / SATA3 HDD:

Points of attention, before you process the Hot Unplug:

Please do follow below instruction sequence to process the Hot Unplug, improper procedure will cause the SATA / SATAII / SATA3 HDD damage and data loss.

Step 1

Unplug SATA data cable from SATA / SATAII / SATA3 HDD side.

Step 2

Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII / SATA3 HDD side.

47

Image 47

Contents P67 Extreme4 Gen3 Disclaimer Copyright NoticeContents Utilities Menu Introduction Uefi Menu BarIntroduction Package ContentsSpecifications USB3.0 ConnectorSmart Switch Hardware Bios FeatureUnique Feature Support CDPage Page Page 24.4cm 9.6 Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Screw Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Conﬁgurations Installation of Memory Modules DimmNotch break Break Installing a DimmPcie slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Requirements Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card Double-click Nvidia Settings icon on your Windows taskbar Driver Installation and SetupFor Windows XP / XP 64-bit OS For Slitm mode only Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows 7 / VistaTM OS Install the required drivers to your systemFor Windows XP OS Page Description Surround Display FeatureJumpers Setup \ Surround Display InformationOnboard Headers and Connectors USB 3.0 Header USB 2.0 HeadersFunctions System Panel HeaderSeveral system front panel Speaker to this header Chassis Speaker HeaderATX 12V Power Connector ATX Power Connector Please connect an ATX powerSupply to this connector Serial port module Installation Guide of Front USB 3.0 PanelSerial port Header Smart Switches Installation Guide of Rear USB 3.0 BracketStatus Code Description 13 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Hot Plug and Hot Swap Functions for SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for Sata / Sataii HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Unplug Points of attention, before you process the Hot PlugMake a Sata / Sataii / SATA3 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up UefiUse RAID Installation Guide to set RAID conﬁguration Setting Up a RAID Ready SystemMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen OC Tweaker Screen Write Recovery Time tWR Dram Timing Control Dram Conﬁguration Load XMP SettingRAS# to CAS# Delay tRCD Command Rate CRMemory Power Down Mode RAS to RAS Delay tRRDWrite to Read Delay tWTR Memory Fast BootVTT Voltage Use this to select VTT Voltage. The default value is AutoUse this to select Vccsa Voltage. The default value is Auto User DefaultInstant Flash Advanced ScreenCPU Configuration Local x2APIC CPU Thermal ThrottlingIntel Virtualization Technology No-Excute Memory ProtectionPrimary Graphics Adapter North Bridge ConfigurationLow Mmio Align VT-dSouth Bridge Configuration Onboard Debug Port LED Sata Mode Storage ConfigurationMarvell SATA3 Operation Mode Marvell SATA3 BootableSuper IO Configuration Acpi Configuration Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Contact Information Software SupportInstalling OS on a HDD Larger Than 2TB