ASRock P67 Extreme4 Gen3 manual Installation Guide of Front USB 3.0 Panel, Serial port Header

Page 38

Serial port Header	This COM1 header supports a
(9-pin COM1)	serial port module.
(see p.12 No. 34)

HDMI_SPDIF Header

(2-pin HDMI_SPDIF1)

(see p.12 No. 36)

1

GND

SPDIFOUT

HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.

The Installation Guide of Front USB 3.0 Panel

Step 1 Prepare the bundled Front USB 3.0 Panel, four Step 2 HDD screws, and six chassis screws.

Screw the 2.5” HDD/SSD to the Front USB 3.0 Panel with four HDD screws.

Step 3

Intall the Front USB 3.0 Panel into the 2.5” drive bay of the chassis.

Step 4

Screw the Front USB 3.0 Panel to the drive bay with six chassis screws.

Step 5

Plug the Front USB 3.0 cable into the USB 3.0 header (USB3_2_3) on the motherboard.

Step 6

The Front USB 3.0 Panel is ready to use.

38

Image 38

Contents P67 Extreme4 Gen3 Copyright Notice DisclaimerContents Introduction Uefi Menu Bar Utilities MenuPackage Contents IntroductionSpecifications USB3.0 ConnectorSmart Switch Support CD Bios FeatureUnique Feature HardwarePage Page Page Motherboard Layout 24.4cm 9.6Table for Audio Output Connection I/O PanelLAN Port LED Indications Page Pre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConﬁgurationsInstalling a Dimm Notch break BreakPcie slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Slitm and Quad Slitm Operation Guide RequirementsASRock SLIBridge2S Card Double-click Nvidia Settings icon on your Windows taskbar Driver Installation and SetupFor Windows XP / XP 64-bit OS For Slitm mode only Select Nvidia Control Panel tab Select Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows 7 / VistaTM OS Install the required drivers to your systemFor Windows XP OS Page \ Surround Display Information Surround Display FeatureJumpers Setup DescriptionOnboard Headers and Connectors USB 2.0 Headers USB 3.0 Header Functions System Panel Header Several system front panel Chassis Speaker Header Speaker to this headerATX 12V Power Connector ATX Power Connector Please connect an ATX powerSupply to this connector Serial port module Installation Guide of Front USB 3.0 PanelSerial port Header Installation Guide of Rear USB 3.0 Bracket Smart Switches13 Dr. Debug Status Code DescriptionPage Page Page Serial ATA3 SATA3 Hard Disks Installation Hot Plug and Hot Swap Functions for Sata / Sataii HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Plug Points of attention, before you process the Hot UnplugSet up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Make a Sata / Sataii / SATA3 Driver DisketteSetting Up a RAID Ready System Use RAID Installation Guide to set RAID conﬁgurationMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Introduction Uefi Menu BarTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen OC Tweaker Screen Command Rate CR Dram Timing Control Dram Conﬁguration Load XMP SettingRAS# to CAS# Delay tRCD Write Recovery Time tWRMemory Fast Boot RAS to RAS Delay tRRDWrite to Read Delay tWTR Memory Power Down ModeUser Default Use this to select VTT Voltage. The default value is AutoUse this to select Vccsa Voltage. The default value is Auto VTT VoltageAdvanced Screen Instant FlashCPU Configuration No-Excute Memory Protection CPU Thermal ThrottlingIntel Virtualization Technology Local x2APICVT-d North Bridge ConfigurationLow Mmio Align Primary Graphics AdapterSouth Bridge Configuration Onboard Debug Port LED Marvell SATA3 Bootable Storage ConfigurationMarvell SATA3 Operation Mode Sata ModeSuper IO Configuration Acpi Configuration USB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Contact InformationInstalling OS on a HDD Larger Than 2TB