ASRock P67 Extreme4 Gen3 manual Boot Screen

Page 71

3.6 Boot Screen

In this section, it will display the available devices on your system for you to conﬁg- ure the boot settings and the boot priority.

Setup Prompt Timeout

This shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means indeﬁnite waiting.

Bootup Num-Lock

If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

Full Screen Logo

Use this item to enable or disable OEM Logo. The default value is [Enabled].

AddOn ROM Display

Use this option to adjust AddOn ROM Display. If you enable the option “Full Screen Logo” but you want to see the AddOn ROM information when the system boots, please select [Enabled]. Conﬁguration options: [Enabled] and [Disabled]. The default value is [Enabled].

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN feature.

Boot Failure Guard

Enable or disable the feature of Boot Failure Guard.

Boot Failure Guard Count

Enable or disable the feature of Boot Failure Guard Count.

71

Image 71

Contents P67 Extreme4 Gen3 Disclaimer Copyright NoticeContents Utilities Menu Introduction Uefi Menu BarIntroduction Package ContentsSpecifications USB3.0 ConnectorSmart Switch Hardware Bios FeatureUnique Feature Support CDPage Page Page 24.4cm 9.6 Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Screw Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Conﬁgurations Installation of Memory Modules DimmNotch break Break Installing a DimmPcie slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Requirements Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card Double-click Nvidia Settings icon on your Windows taskbar Driver Installation and SetupFor Windows XP / XP 64-bit OS For Slitm mode only Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows 7 / VistaTM OS Install the required drivers to your systemFor Windows XP OS Page Description Surround Display FeatureJumpers Setup \ Surround Display InformationOnboard Headers and Connectors USB 3.0 Header USB 2.0 HeadersFunctions System Panel HeaderSeveral system front panel Speaker to this header Chassis Speaker HeaderATX 12V Power Connector ATX Power Connector Please connect an ATX powerSupply to this connector Serial port module Installation Guide of Front USB 3.0 PanelSerial port Header Smart Switches Installation Guide of Rear USB 3.0 BracketStatus Code Description 13 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Hot Plug and Hot Swap Functions for SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for Sata / Sataii HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Unplug Points of attention, before you process the Hot PlugMake a Sata / Sataii / SATA3 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up UefiUse RAID Installation Guide to set RAID conﬁguration Setting Up a RAID Ready SystemMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen OC Tweaker Screen Write Recovery Time tWR Dram Timing Control Dram Conﬁguration Load XMP SettingRAS# to CAS# Delay tRCD Command Rate CRMemory Power Down Mode RAS to RAS Delay tRRDWrite to Read Delay tWTR Memory Fast BootVTT Voltage Use this to select VTT Voltage. The default value is AutoUse this to select Vccsa Voltage. The default value is Auto User DefaultInstant Flash Advanced ScreenCPU Configuration Local x2APIC CPU Thermal ThrottlingIntel Virtualization Technology No-Excute Memory ProtectionPrimary Graphics Adapter North Bridge ConfigurationLow Mmio Align VT-dSouth Bridge Configuration Onboard Debug Port LED Sata Mode Storage ConfigurationMarvell SATA3 Operation Mode Marvell SATA3 BootableSuper IO Configuration Acpi Configuration Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Contact Information Software SupportInstalling OS on a HDD Larger Than 2TB