ASRock P67 Extreme4 Gen3 manual

Page 43

0xA6	SCSI Detect
0xA7	SCSI Enable
0xA8	Setup Verifying Password
0xA9	Start of Setup
0xAA	Reserved for ASL (see ASL Status Codes section below)
0xAB	Setup Input Wait
0xAC	Reserved for ASL (see ASL Status Codes section below)
0xAD	Ready To Boot event
0xAE	Legacy Boot event
0xAF	Exit Boot Services event
0xB0	Runtime Set Virtual Address MAP Begin
0xB1	Runtime Set Virtual Address MAP End

0xB2	Legacy Option ROM Initialization
0xB3	System Reset
0xB4	USB hot plug
0xB5	PCI bus hot plug
0xB6	Clean-up of NVRAM
0xB7	Conﬁguration Reset (reset of NVRAM settings)

0xB8 – 0xBF	Reserved for future AMI codes
0xC0 – 0xCF	OEM BDS initialization codes
0xD0	CPU initialization error
0xD1	North Bridge initialization error
0xD2	South Bridge initialization error
0xD3	Some of the Architectural Protocols are not available
0xD4	PCI resource allocation error. Out of Resources
0xD5	No Space for Legacy Option ROM
0xD6	No Console Output Devices are found
0xD7	No Console Input Devices are found

0xD8	Invalid password
0xD9	Error loading Boot Option (LoadImage returned error)
0xDA	Boot Option is failed (StartImage returned error)
0xDB	Flash update is failed
0xDC	Reset protocol is not available

43

Image 43

Contents P67 Extreme4 Gen3 Disclaimer Copyright NoticeContents Utilities Menu Introduction Uefi Menu BarIntroduction Package ContentsSpecifications Smart Switch ConnectorUSB3.0 Hardware Bios FeatureUnique Feature Support CDPage Page Page 24.4cm 9.6 Motherboard LayoutLAN Port LED Indications I/O PanelTable for Audio Output Connection Page Screw Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Conﬁgurations Installation of Memory Modules DimmNotch break Break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie slots Requirements Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupDouble-click Nvidia Settings icon on your Windows taskbar Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS Install the required drivers to your systemFor Windows 7 / VistaTM OS Page Description Surround Display FeatureJumpers Setup \ Surround Display InformationOnboard Headers and Connectors USB 3.0 Header USB 2.0 HeadersSeveral system front panel System Panel HeaderFunctions Speaker to this header Chassis Speaker HeaderSupply to this connector ATX Power Connector Please connect an ATX powerATX 12V Power Connector Serial port Header Installation Guide of Front USB 3.0 PanelSerial port module Smart Switches Installation Guide of Rear USB 3.0 BracketStatus Code Description 13 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Hot Plug and Hot Swap Functions for SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for Sata / Sataii HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Unplug Points of attention, before you process the Hot PlugMake a Sata / Sataii / SATA3 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up UefiUse RAID Installation Guide to set RAID conﬁguration Setting Up a RAID Ready SystemMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Set up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen OC Tweaker Screen Write Recovery Time tWR Dram Timing Control Dram Conﬁguration Load XMP SettingRAS# to CAS# Delay tRCD Command Rate CRMemory Power Down Mode RAS to RAS Delay tRRDWrite to Read Delay tWTR Memory Fast BootVTT Voltage Use this to select VTT Voltage. The default value is AutoUse this to select Vccsa Voltage. The default value is Auto User DefaultInstant Flash Advanced ScreenCPU Configuration Local x2APIC CPU Thermal ThrottlingIntel Virtualization Technology No-Excute Memory ProtectionPrimary Graphics Adapter North Bridge ConfigurationLow Mmio Align VT-dSouth Bridge Configuration Onboard Debug Port LED Sata Mode Storage ConfigurationMarvell SATA3 Operation Mode Marvell SATA3 BootableSuper IO Configuration Acpi Configuration Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Contact Information Software SupportInstalling OS on a HDD Larger Than 2TB