ASRock p4i65pe manual Chipset Configuration

Page 23

of this motherboard. If it shows “Locked”, then the item Ratio CMOS Set- ting will be hidden. If you use the ratio value to time the CPU frequency, it will be equal to the core speed of the installed processor.

Ratio Actual Value

This is a read-only item, which displays the ratio actual value of this motherboard.

CPU Thermal Throttling

You may select [Enabled] to enable P4 CPU internal thermal control mecha- nism to keep the CPU from overheated.

Hyper Threading Technology

To enable this feature, it requires a computer system with an Intel Pentium®4 processor that supports Hyper-Threading technology and an operating sys- tem that includes optimization for this technology, such as Microsoft® Win- dows® XP. Set to [Auto] if using Microsoft® Windows® XP, or Linux kernel version 2.4.18 or higher. This option will be hidden if the installed CPU does not support Hyper-Threading technology.

Max CPUID Value Limit

For Prescott CPU only, some OSes (ex. NT4.0) cannot handle the function with disable. This should be enabled in order to boot legacy OSes that cannot support CPUs with extended CPUID functions.

3.3.2 Chipset Configuration

BIOS SETUP UTILITY

Advanced

Chipset Configuration

Bypass Access

[Off]

DRAM Frequency

[Auto]

Flexibility Option

[Disabled]

Configure DRAM Timing by SPD

[Disabled]

DRAM CAS# Latency

[Auto]

DRAM RAS# Precharge

[4 Clocks]

DRAM RAS# to CAS# Delay

[4 Clocks]

DRAM Precharge Delay

[8 Clocks]

DRAM Burst Length

[4]

Memory Hole

[Disabled]

Init. Graphic Adapter Priority

[PCI / AGP]

Graphics Aperture Size

[64MB]

OnBoard LAN

[Enabled]

OnBoard AC'97 Audio

[Auto]

Options

133MHz (DDR266) 166MHz (DDR333) 200MHz (DDR400) Auto

 

Select Screen

 

Select Item

+ -

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

Bypass Access

This technology can provide users with the function of increasing the sys- tem performance. The default value is [Disabled]. It will only work when you use FSB800 CPU and DDR400 DRAM at the same time; otherwise, this option will be hidden.

2 3

Image 23
Contents P4i65PE Disclaimer Copyright NoticeContents Software Support Introduction Package ContentsSpecifications Bios 20.8cm 8.2 Motherboard LayoutTable for Audio Output Connection ASRock 8CH I/OPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Installing a DimmExpansion Slots PCI and AGP Slots Installing an expansion cardPS2USBPWR1 Jumpers SetupIDE2 Onboard Headers and ConnectorsUSB 2.0 Header Chassis Speaker Header Serial ATA Sata Hard Disks Installation Bios Menu Bar Bios Setup UtilityAdvanced Screen Navigation KeysMain Screen Ratio Status CPU ConfigurationCPU Host Frequency Spread SpectrumChipset Configuration Dram Frequency Configure Dram Timing by SPDDram RAS# to CAS# Delay Dram Precharge DelayAcpi Configuration OnBoard IDE Controller IDE ConfigurationOnBoard IDE Operate Mode Combined Mode OptionLBA/Large Mode IDE Device ConfigurationPCIPnP Configuration Serial Port Address Floppy ConfigurationSuper IO Configuration OnBoard Floppy ControllerEPP Version Parallel Port ModeECP Mode DMA Channel Parallel Port AddressUSB 2.0 Support USB ConfigurationHardware Health Event Monitoring Screen USB ControllerBoot Up Num-Lock Boot ScreenBoot Settings Configuration Boot From NetworkHDD PM-MAXTOR 6L08 Boot Device PrioritySecurity Screen Discard Changes and Exit Load Optimal DefaultsExit Screen Save Changes and ExitSoftware Support