ASRock K10N78hSLI-GLAN manual PCIPnP Configuration, A.R.T, 32Bit Data Transfer, PCI Latency Timer

Page 53

S.M.A.R.T.

Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled].

32Bit Data Transfer

Use this item to enable 32-bit access to maximize the IDE hard disk data transfer rate.

3.3.5 PCIPnP Configuration

BIOS SETUP UTILITY

Advanced

Advanced PCI / PnP Settings

PCI

Latency Timer

[32]

PCI

IDE BusMaster

[Enabled]

Value in units of PCI clocks for PCI device latency timer register.

 

Select Screen

 

Select Item

+-

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

Setting wrong values in this section may cause the system to malfunction.

PCI Latency Timer

The default value is 32. It is recommended to keep the default value unless the installed PCI expansion cards’ specifications require other settings.

PCI IDE BusMaster

Use this item to enable or disable the PCI IDE BusMaster feature.

53

Image 53
Contents K10N78hSLI-GLAN Disclaimer Copyright NoticeContents Software Support Bios Setup UtilityIntroduction Package ContentsSpecifications Unique Feature Bios FeatureSupport CD HardwarePage Page CPU DDR2 Motherboard LayoutTable for Audio Output Connection ASRock eSATAIISPDIF I/OPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardSupported PCI Express Card for Hybrid Slitm Minimum System Configuration for Hybrid SlitmHybrid Slitm Operation Guide Enjoy the benefit of Nvidia Hybrid Slitm PS2USBPW1 Jumpers SetupIDE1 Onboard Headers and ConnectorsSerial ATA Sata Power Cable Header CPU Fan Connector White end 2-pin Hdmispdif Header Connection Guide ESATAII Interface Introduction What is eSATAII?How to install eSATAII? Comparison between eSATAII and other devices Western Digital Sataii Hard Disk Setup GuidePage What is Hot Swap Function? What is Hot Plug Function?Points of attention, before you process the Hot Plug Sata / Sataii HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a Sata / Sataii HDD How to Hot Plug a Sata / Sataii HDDMake a Sata / Sataii driver diskette Driver Installation GuideInstalling Windows XP / XP 64-bit Without RAID Functions Install Windows VistaTM / VistaTM 64-bit OS on your system Install Windows XP / XP 64-bit OS on your systemUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit With RAID Functions\ RAID Installation Guide \ I386 \ AHCIVista For Windows VistaTM OSSet the Sata Operation Mode option to RAID Untied Overclocking Technology Introduction Bios Menu BarMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondCPU Configuration Monitor Boot Security ExitAdvanced Screen MainBoot Failure Guard Overclock ModeAM2 Boost CPU Frequency MHzEnhanced Halt State Secure Virtual MachineProcessor Maximum Frequency North Bridge Maximum FrequencyProcessor Target Frequency Processor VoltageNorth Bridge Target Frequency CPU Frequency MultiplierCAS Latency CL Memory Controller ModeFlexibility Option CS/ODT Fine Delay Addr/Cmd Fine DelayMA Timing Bank InterleavingHybrid SLI Front PanelShare Memory Primary Graphics AdapterCPU NB Link Width CPU NB Link SpeedDram Voltage Chipset Core VoltageAcpi Configuration IDE Device Configuration Sata Operation ModeAcpi Hpet Table OnBoard IDE ControllerPIO Mode LBA/Large ModeDMA Mode Block Multi-Sector TransferPCI Latency Timer PCIPnP ConfigurationA.R.T 32Bit Data TransferSuper IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Controller Enabled USB ConfigurationUSB Controller USB 2.0 SupportHardware Health Event Monitoring Screen Target CPU TemperatureCPU Quiet Fan Target Fan SpeedBoot Settings Configuration Boot ScreenBoot From Onboard LAN Boot Up Num-LockSecurity Screen Main Advanced Monitor BootChange Supervisor Password Exit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers Menu